Optimum B 34 H Vario Operating Manual Download Page 29

Page: 29 / 78

OPTIMUM

M A S C H I N E N - G E R M A N Y

Operation

21 / 07 / 2014

Page 29

Operation Upright drill B34 H/ B34 H Vario ; Version 1.0.5



014

Operation

4.1

Safety

Use the machine only under the following conditions:



The machine is in proper working order.



The machine is used as prescribed.



The instruction manual has been followed.



All safety devices are installed and activated.

All malfunctions should be eliminated immediately. Stop the machine immediately at an event of
any malfunction in operation and make sure it cannot be started up accidentally or without
authorisation.

Notify the person responsible immediately of any modification.



„Safety during operation“ on page 14

4.2

Control and indicating elements

4.2.1

Upright drill B34 H (Vario)

Img.4-1: B34 H Img.:B34 H Vario

belt drive with housing

handle for belt tension

handle for spindle feed

Push button ON/OFF

EMERGENCY-STOP

cooling equipment

(B34 H Vario)

heignt adjustment for the

drilling table

cooling pump

belt drive with housing

handle for spindle feed

EMERGENCY-STOP

Push button ON/ OFF

drill chuck guard

drilling table

height adjustment for the

drilling table

Summary of Contents for B 34 H Vario















































































Search results

Summary of Contents for B 34 H Vario

Reviews:

Related manuals for B 34 H Vario

Brands by name

Popular brands

Optimum B 34 H Vario, Operating Manual

Search results

Summary of Contents for B 34 H Vario

Reviews:

Related manuals for B 34 H Vario

Brands by name

Popular brands