manualshive.com logo in svg

Optimum B 34 H Vario, Operating Manual

Share
Download
Optimum B 34 H Vario Operating Manual Download Page 12

Safety

OPTIMUM

M A S C H I N E N   -   G E R M A N Y

21 / 07 / 2014

Page 12

Safety  Upright drill B34 H/ B34 H Vario ; Version 1.0.5



 201

4

US

1.9

EMERGENCY-STOP-BUTTON

CAUTION!

After actuating the EMER-
GENCY-STOP-button the drill-
ing spindle will turn some 
more seconds depending on 
the previously set speed.

.

Img.1-1:   EMERGENCY-STOP B34 H (Vario)

1.10

Drilling table

The drilling table is equipped
with T-slots for clamping
blocks.

WARNING!

Risk of injury due to parts 
flying off at high speed. 
Securely fix the workpiece 
on the drilling table.

Img.1-2:   Drilling table

limit switch protective 
cover 
V-belts

The upright drill must not switch on, if the protective cover 
of the pulleys is opened.

drill chuck guard

The upright drill must only switch on when the drill chuck 
guard is closed.

Functional test

Item

Inspection

OK

Date:

 Inspector (signature):

EMERGENCY-

STOP-button

T-slots for clamping

blocks

(14 mm)

Summary of Contents for B 34 H Vario















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands