OnRobot HEX-E v1 User Manual Download

Page: 11 / 68

Getting Started

www.onrobot.com

Legend: 1 –robot tool flange, 2 – Adapter A, 3 - M6x8 screws, 4 – M4x8
screws, 5 – overload plug, 6 – M6x30 screw, 7 – sensor, 8 – M4 washer, 9 –
M4x12 screw, 10 – cable holder

Fasten the tool to the Sensor, according to the instructions from the tool

manufacturer.

The overload protection is not fully functional, if the tool is not joined

to the Sensor with a flat surface.

2.3.2

HEX-E v2 and HEX-H v2

To mount the sensor, follow this process:

Fasten Adapter-A2 to the Robot by four M6x8 Torx Screws with M6

washers. Use 6 Nm tightening torque.

Fasten the Sensor to the adapter by five M4x86 screws with M4 washers.

Use 1,5 Nm tightening torque.

Fasten the cable to the Sensor with the Cable Holder by one M4x12 screw
and M4 washer. Use 1,5 Nm tightening torque.

Fasten the Plug to the Sensor by one M6x30 Screw. Use 6 Nm tightening

torque.

Legend: 1 –robot tool flange, 2 – Aadapter- A2, 3 - M6 washer, 4 – M6x8 Torx
screws, 4, 5 – sensor, 6 – M4x6 Torx screws, 7 – cable holder

Summary of Contents for HEX-E v1





































































Search results

Summary of Contents for HEX-E v1

Reviews:

Related manuals for HEX-E v1

Brands by name

Popular brands

OnRobot HEX-E v1, User Manual

Search results

Summary of Contents for HEX-E v1

Reviews:

Related manuals for HEX-E v1

Brands by name

Popular brands