background image

 

 

Preface

  

5

 

OnRobot © 2018 

 

www.onrobot.com 

 

Copyright © 2017-2018 OnRobot A/S. All rights Reserved. No part of this publication 
may be reproduced, in any form or by any means, without the prior written 
permission of OnRobot A/S.

 

Information provided within this document is accurate to the best of our knowledge 
at the time of its publication. There may be differences between this document and 
the product if the product has been modified after the edition date. 

OnRobot A/S. does not assume any responsibility for any errors or omissions in this 
document. In no event shall OnRobot A/S. be liable for losses or damages to persons 
or property arising from the use of this document. 

The information within this document is subject to change without notice. You can 
find the latest version on our webpage at: 

https://onrobot.com/

. 

The original language for this publication is English. Any other languages that are 
supplied have been translated from English. 

All trademarks belong to their respective owners. The indications of (R) and TM are 
omitted. 

 

 

Summary of Contents for HEX-E v1





































































Reviews: