![background image](http://html.mh-extra.com/html/onkyo/29400468/29400468_instruction-manual_1637358020.webp)
20
En
You can temporarily mute the output of the AV receiver.
Tip
• To unmute, press
MUTING
again or adjust the volume.
• The Mute function is cancelled when the AV receiver is set to
Standby.
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
Tip
• If you need to cancel the sleep timer, press
SLEEP
repeatedly
until the
SLEEP
indicator goes off.
• To check the time remaining until the AV receiver sleeps, press
SLEEP
. Note that if you press
SLEEP
while the sleep time is
being displayed, you’ll shorten the sleep time by 10 minutes.
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the
PHONES
jack, the
speakers are turned off.
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it’s already set to Stereo, Mono, or Direct.
• Only the Stereo, Direct and Mono listening modes can be used
with headphones.
When you connect an
u
-capable Onkyo component, you
must configure the input display so that
u
can work
properly.
This setting can be done only from the front panel.
Note
•
DOCK
can be selected for the
TV/CD
,
GAME
or
VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (
➔
40
).
You can use two sets of front speakers with the AV
receiver:
Speakers A
for up to 5.1-channel playback in
your main listening room and
Speakers B
for 2-channel
stereo playback in another room.
Note
• While Speakers B is on, channels are reduced to 2.1 in the main
room (
➔
10
).
Tip
• Alternatively, you can use the AV receiver’s
SPEAKERS
A
and
B
.
Muting the AV Receiver
Press
RECEIVER
followed by
MUTING
.
The output is muted and the
MUTING
indicator
flashes on the display.
Using the Sleep Timer
Press
RECEIVER
followed by
SLEEP
repeatedly
to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in
10 minute steps.
The
SLEEP
indicator lights on the display when the
sleep timer has been set. The specified sleep time
appears on the display for about five seconds, then
the previous display reappears.
Using Headphones
Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the
PHONES
jack.
Changing the Input Display
1
Press
TV/CD
,
GAME
or
VCR/DVR
on the front
panel so that “TV/CD”, “GAME” or “VCR/DVR”
appears on the display.
2
Press and hold down
TV/CD
,
GAME
or
VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select “
MD
”, “
CDR
”, “
DOCK
”
or “
TAPE
”.
For the
TV/CD
input selector, the input display
changes in this order:
For the
GAME
input selector, the setting changes in
this order:
For the
VCR/DVR
input selector, the setting
changes in this order:
Selecting Speakers A and B
Press
RECEIVER
followed by
SP A/B
repeatedly
to cycle through the selection:
A
or
B
, or both indicators light on the display.
TV/CD
→
MD
→
CDR
DOCK
→
→
TAPE
→
GAME
↔
DOCK
VCR/DVR
↔
DOCK
Speakers A
→
Speakers A&B
→
Speakers B
→
Off
←
Summary of Contents for 29400468
Page 51: ...51 En Memo ...