OMT STAND.MOVE M1.0 Operation Manual Download

Page: 23 / 23

STAND: 17.06.2019

9910_Operation-Manual_STANDMOVE_M1-0_Rev1v0_EN

Seite 23 von 23

15 Additional Information

Copyright

Metalltechnik

GmbH.

ating manual may be copied or reproduced without the written consent of Oelschläger

Metalltechnik

GmbH. Oelschläger

Metalltechnik

GmbH reserves the right to make changes to the specifications and

other information in this operating manual without prior notice.

Licences

After procurement and complete payment of the product, the customer may use the running texts and

graphics in chapter 9 for generating the end user documentation for the height-adjustable table, in which

the STAND.MOVE M1.0 was integrated, for 10 years from delivery, free of charge. This licence does

not include any logo, design or page layout elements of Oelschläger

Metalltechnik

GmbH. The cus-

tomer may make all the necessary changes to the text and graphics to match them to the purpose of

the end-user documentation. The texts and graphics may not by published or sub-licensed, either un-

changed or modified, through the digital route. The transfer of this license to third parties without per-

mission from Oelschläger

Metalltechnik

GmbH is also prohibited. The entire right of ownership and

Metalltechnik

GmbH. The texts and

graphics are offered as is, without any warranty or assurances of any kind.

Contact our customer service to get the text and graphics in an editable format.

Trademarks

Documentation can also contain, among other things, the depiction of registered trademarks of goods

or services as well as information on copyright or other protected know-how of Oelschläger

Metalltechnik

GmbH or third parties. In all cases, all the rights remain exclusively with the respective

holder.

Address

Oelschläger

Metalltechnik

GmbH

Hertzstraße 1-3

27318 Hoya – Germany

Tel.:

+49 (0) 4251 – 816 – 0

Email:

[email protected]

Internet:

www.oelschlaeger.de

Registered office of the company: Hoya (Germany)

District Court of Walsrode - HRB 31030

CEO: Andreas Spreen

Summary of Contents for STAND.MOVE M1.0
























Search results

Summary of Contents for STAND.MOVE M1.0

Reviews:

Related manuals for STAND.MOVE M1.0

Brands by name

Popular brands

OMT STAND.MOVE M1.0, Operation Manual

Search results

Summary of Contents for STAND.MOVE M1.0

Reviews:

Related manuals for STAND.MOVE M1.0

Brands by name

Popular brands