background image

http://www.orion.ua

4

Setting the temperature

Fabric

Temperature control

NYLON/ACRYLIC/ACETATE

SILK/RAYON/POLYESTER

WOOL/COTTON

LINEN

MAX

1.  Stand the iron on its heel and plug the power cord into wall socket.
2. Turn the iron temperature control knob until you get the desired

fabric/temperature setting. We recommend using the above table as a guide.

3.  The temperature pilot light will light, indicating that the soleplate is heating up.
4.  When the pilot light goes out, the required temperature has been reached. The

temperature pilot light will go on from time to time during ironing.

Dry ironing

1.  Set the steam button to position «0» or «

».

2. Turn the temperature control knob to select the desired fabric/temperature

setting. The indicator pilot light will light, put the iron on the smooth and stable
place vertically.

3. When the indicator pilot light goes out, the required temperature has been

reached.

4.  You can begin to iron.

Spraying

1.  Ensure there is enough water in the water tank.
2.  Press the spray button to produce a fine spray of spray nozzle and continue

ironing

Note:

Do not spray silk.

Steam ironing

1.  As indicated on the temperature control and the table on the iron, steam-ironing

is only possible at higher ironing temperatures (between “

” to “MAX”).

2.  Ensure that there is enough water in the water tank.
3.  Stand the iron on its end; Insert the main plug into the wall socket.
4.  Set the temperature control knob at the required position within the steam area.
5.  After the indicator pilot light has gone out and has come on again, you may start

ironing.

6.  Turn the steam control knob to the required position.

Note:

  Never direct the steam towards people and animals. Burns or serious injury may

occur.

Strong steam

This function is used to iron out deep wrinkles, to iron cuffs and coarse fabrics.

1.  Ensure that there is enough water in the water tank.
2.  When the temperature control knob is set to steam setting (between “

” to

“MAX”) strong steam can be used.

3.  Press the burst steam button, the soleplate will spray out strong steam.

Summary of Contents for ORI-025







Reviews: