K8AC-H
17
Parameter List
The setting items in each mode are called “parameters.”
Parameters can be switched by using the
M
key.
Power supply voltage
measurement value
*
1
Voltage fluctuation
compensation standard value
Number of
CT passes 1
CT ratio 1
Number of
CT passes 2
CT ratio 2
*
3
Parameter Display
: Displayed for all models and settings.
: May not be displayed depending on the model or settings.
Setting change protection
*
3
*
3
*
3
*
2
*
2
*
4
Voltage fluctuation
compensation standard value
Setting 1 for number of
effective digits to be displayed
after the decimal point
Setting 2 for number of
effective digits to be displayed
after the decimal point
init
sini
pini
hys1
hys2
gate
comp
stim
odly
soft
ssht
sopn
hrst
hral
msmd
dsel
psmd
pstm
dsmd
dsrf
u no
bps
len
sbit
nct1
ctr1
ndp1
nct2
ctr2
ndp2
prty
goht
al-1
al-2
ct 1
ct 2
sce
max1
min1
max2
min2
maxs
isc2
isc1
otim
memo
acnt
min5
1234
VfcV
amoV
aspt
wtpt
test
g-lV
sdly
sglV
cyct
Heater 1 current
Heater 2 current
Heater 1
maximum current
Heater 1
minimum current
Heater 2
maximum current
Heater 2
minimum current
Maximum power
supply voltage
(Processing value
display status)
Heater 2 input shift
display current
Heater 1 input shift
display current
Minimum power
supply voltage
Number of
alarm outputs
Processing value
for alarm output
RUN time
Password for
moving to Set
Mode: 0169
Burnout alarm
setting value 1
Heater layer short circuit
detection function
SSR open circuit
detection function
SSR short circuit
detection function
Output ON-delay time
Soft startup time
Startup lock time
Gate input function
Alarm hysteresis 2
Alarm hysteresis 1
Processing value
initialization
All initialization
Set value initialization
Heater control
method
Switchable
display
Power save
mode
Power save
mode standby
time
Display mode
Display
refresh time
Unit number
Baud rate
SSR ON delay
SSR operation
gate current level
Cycle time
Data length
Stop bits
Parity bit
Gate OFF
output hold time
Protection Mode
Adjust Mode
Run Mode
Measurement
parameters
Set Mode
Setting change protection
1 s min.
1 s min.
1 s min.
3 s min.
Po
w
er ON
5 s min.
Burnout alarm
setting value 2
1 s min.
1 s min.
1 s min.
Test Mode
Gate Mode
1 s min.
An alarm is output if
the test value falls
below the burnout
alarm value 1 setting.
Alarm or detection is
stopped if the gate
current value falls
below the set value.
Note:
Displayed only for
the K8AC-H2
@@@
.
Heater layer short circuit
alarm set value
*1.
Displayed when the Selectable Protection Level parameter is set to 0.
*2.
Displayed by the K8AC-H
@@
P
@
-FLK.
*3.
If more than five minutes elapses with no operations performed in Protection Settings Mode, Adjust Mode, Set Mode, or for a measurement
parameter, the status will return automatically to the processing value display.
If this occurs while settings are in progress, it may cause unintended operations to be performed in Run Mode (i.e., with measurement values
displayed). Be careful not to allow this to happen.
*4.
Displayed by the K8AC-H
@@
C
@
-FLK.
