background image

G-124

Safety Sensors / Components

Specifications

Ratings

Power Input

Inputs

Note: Indicates the current between terminals A1 and A2.

Contacts

Characteristics

Note: 1. The contact resistance was measured with 1 A at 5 VDC using the voltage-drop method.

2. The bounce time is not included in the figure for operating time.
3. The response time is the time it takes for the main contact to open after the input is turned OFF.
4. The insulation resistance was measured with 500 VDC at the same places that the dielectric strength was checked.

Item

G9SB-200

#

-

#

G9SB-3010

G9SB-301

#

-

#

Power supply voltage

24 VAC/VDC: 24 VAC, 50/60 Hz, or 24VDC
24 VDC: 24 VDC

Operating voltage range 85% to 110% of rated power supply voltage

Power consumption

1.4 VA/1.4 W max.

1.7 W max.

1.7 VA/1.7 W max.

Item

G9SB-200

#

-

#

G9SB-3010

G9SB-301

#

-

#

Input current

25 mA max.

60 mA max. (See note.)

30 mA max.

Item

G9SB-200

#

-

#

G9SB-3010

G9SB-301

#

-

#

Resistive load (cos =1)

Rated load

250 VAC, 5 A

Rated carry current

5 A

Item

G9SB-200

#

-

#

G9SB-3010

G9SB-301

#

-

#

Contact resistance (See note 1.)

100 m

Operating time (See note 2.)

30 ms max.

Response time (See notes 2 and 3.)

10 ms max.

Insulation resistance (See note 4.)

100 M

 min. (at 500 VDC)

Dielectric strength

Between different 
outputs

2,500 VAC, 50/60 Hz for 1 min

Between inputs 
and outputs

Between power in-
puts and outputs

Vibration resistance

10 to 55 to 10 Hz, 0.375-mm single amplitude (0.75-mm double amplitude)

Shock resistance

Destruction

300 m/s

2

Malfunction

100 m/s

2

Durability

Mechanical

5,000,000 operations min. (at approx. 7,200 operations/hr)

Electrical

100,000 operations min. (at approx. 1,800 operations/hr)

Minimum permissable load 
(reference value)

5 VDC, 1 mA

Ambient operating temperature

-25 to 55°C (with no icing or condensation)

Ambient operating humidity

35% to 85%

Terminal tightening torque

0.5 N·m

Weight

Approx. 115 g

Approx. 135 g

Approx. 120 g

Approved standards

EN954-1, EN60204-1, UL508, CSA C22.2 No. 14

EMC

EMI: EN55011 group 1 class A
EMS: EN50082-2

F502-EN2-04.book  Seite 124  Dienstag, 26. Juli 2005  5:48 17

Summary of Contents for G9SB









Reviews: