background image

E5AX-P

E5AX-P

3

 

Characteristics

Setting accuracy

(

+

0.3% of set value or 

+

1

%

C, whichever greater), 

+

1 digit max.

Indication accuracy

(

+

0.3% of set value or 

+

1

%

C, whichever greater), 

+

1 digit max. (Set value coincides with the

indicated value, because no relative error exists between both values.)

Disable band

0.1% to 10.0% (in units of 0.1%)

Proportional band

0.1

%

 to 999.9 

%

C/

%

F (in units of 0.1

%

C/

%

F)

Integral time

1 to 3,999 s (in units of 1 s)

Derivative time

0 to 3,999 s (in units of 1 s)

Alarm output setting range

Thermocouple: –999

%

 to 9,999

%

C/

%

F (in units of 1

%

C/

%

F)

Platinum resistance thermometer: –99.9

%

 to 999.9

%

C/

%

F (in units of 0.1

%

C/

%

F)

Alarm output hysteresis

0.0

%

 to 999.9 

%

C/

%

F (in units of 0.1

%

C/

%

F)

Sampling period

500 ms (temperature sensor input)

Output refresh period

500 ms

Display refresh period

500 ms (temperature sensor input)

Valve travel indication

–99% to 999% (in units of 1%)

Full Open/close time

1 to 999 s ( in units of 1 s)

Input shift

Thermocouple: –999

%

 to 9,999

%

C/

%

F (in units of 1

%

C/

%

F)

Platinum resistance thermometer: –99.9

%

 to 999.9

%

C/

%

F (in units of 0.1

%

C/

%

F)

Insulation resistance

20 M

W

 min. (at 500 VDC)

Dielectric strength

2,000 VAC 50/60 Hz for 1 min between terminals of different polarities

Vibration resistance

Malfunction: 2 to 55 Hz, 2G 10 min each in X, Y, and Z directions
Destruction: 10 to 55 Hz, 0.75-mm double amplitude 2 hrs each in X, Y, and Z directions

Shock resistance

Malfunction: 200 m/s

2

 3 times each in 6 directions

Destruction: 300 m/s

2

 3 times each in 6 directions

Life expectancy

Mechanical: 10,000,000 operations min.
Electrical:

100,000 operations min.

Ambient temperature

Operating: –10

%

 to 55

%

C (with no icing)

Storage:

–25

%

 to 65

%

C (with no icing)

Ambient humidity

Operating: 35% to 85%

Memory protection

Non-volatile memory

Enclosure ratings

Front panel: IEC standard IP50
Rear case: IEC standard IP20
Terminals:

IEC standard IP00

Weight

Standard: Approx. 350 g; Communications: Approx. 480 g; Mounting bracket: Approx. 50 g

*The accuracy of U thermocouples under temperatures from –150

%

 to 400

%

C (–240

%

 to 700

%

F) is 

+

2

%

C (

+

3.6

%

F) 

+

1 digit. Accuracy is

reduced below –150

%

C (–240

%

F). The accuracy of R and S thermocouples under 0

%

 to 200

%

C (0

%

 to 400

%

F) is 

+

3

%

C (

+

5.4

%

F) 

+

1 digit.

Summary of Contents for E5AX-P Series















Reviews: