manualshive.com logo in svg

Omron CV/CVM1, Replacement Manual

Share
Download
Omron CV/CVM1 Replacement Manual Download Page 23

CV/CVM1 instruction 

CS-series Instruction 

Operand 

Number of Operands 

LINE(115) 

LINE(63) 

The data type of the 2nd operand is changed from BCD to BIN. For a constant, the # mark is 
converted to & mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

COLM(116) 

COLM(64) 

The data type of the 3rd operand is changed from BCD to BIN. For a constant, the # mark is   
converted to & mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

TCNT(123) 

None 

This instruction is not supported. Consider programming with the CNT instruction.   

 

TSR(124) 

TSR(780) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

TSW(125) 

TSW(781) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

SSET(160) 

SSET(630) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

SRCH(164) 

SRCH(181) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

MAX(165) 

MAX(182) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

MIN(166) 

MIN(183) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

SUM(167) 

SUM(184) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

EMBC(171) 

EMBC(281) 

The data type of operand is changed from BIN data to BCD. For a constant, the # mark is converted 
to & mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

REGL(175) 

None 

This instruction is not supported. Consider programming with other data transfer instruction.   

 

REGS(176) 

None 

This instruction is not supported. Consider programming with other data transfer instruction. 

 

FPD(177) 

FPD(269) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

FILR(180) 

None 

This instruction is not supported. Consider programming with the FREAD instruction.   

 

FILW(181) 

None 

This instruction is not supported. Consider programming with the FWRIT instruction.   

 

FILP(182) 

None 

This instruction is not supported. Consider the online editing or so. 

 

FLSP(183) 

None 

This instruction is not supported. Consider the online editing or so. 

 

IOSP(187) 

None 

This instruction is not supported. Consider selecting “Normal” for the Execution Mode of CS/CJ. 
(Select “Normal”.for the Execution mode on Peripheral Service tab on the PLC Settings window.). 

 

IORS(188) 

None 

This instruction is not supported. Consider selecting “Normal” for the Execution Mode of CS/CJ. 
(Select “Normal”.for the Execution mode on Peripheral Service tab on the PLC Settings window.). 

 

IODP(189) 

None 

This instruction is not supported. Consider displaying data by using a touch panel or other device. 

 

READ(190) 

None 

This instruction is not supported. Consider programming with the IORD instruction.   
The data of the Special I/O Unit is reflected directly in the I/O memory of PLC. Please refer to the 
operation manual of the Special I/O Unit that you use.   

 

WRIT(191) 

None 

This instruction is not supported. Consider programming with the IOWR instruction.   
The data that is written to the I/O memory of PLC is directly reflected to the Special I/O Unit.    Please 
refer to the operation manual of the Special I/O Unit that you use. 

 

MSG(195) 

MSG(46) 

The data type of the 1st operand is changed from BCD to BIN. For a constant, the # mark is 
converted to & mark. To use word data, change the data type of word from BCD to BIN.   

Same as CV/CVM1 

TOUT 

None 

This instruction is not supported. Consider programming with the OUT instruction.   

 

SA(210) 

SA(784) 

The data specification of operand is different. Refer to the SYSMAC CS/CJ/NSJ Series 
INSTRUCTIONS REFERENCE MANUAL (Cat. No. W474) and CX-Programmer Ver.9.[] 
OPERATION MANUAL SFC Programming (Cat. No. W469), and correct the data. 

Same as CV/CVM1 

SP(211) 

None 

This instruction is not supported. Consider programming with another SFC related instruction. 

 

SR(212) 

None 

This instruction is not supported. Consider programming with another SFC related instruction. 

 

SF(213) 

None 

This instruction is not supported. Consider programming with another SFC related instruction. 

 

SE(214) 

SE(785) 

The data specification of operand is different. Refer to the SYSMAC CS/CJ/NSJ Series 
INSTRUCTIONS REFERENCE MANUAL (Cat. No. W474) and CX-Programmer Ver.9.[] 
OPERATION MANUAL SFC Programming (Cat. No. W469), and correct the data. 

Same as CV/CVM1 

SOFF(215) 

None 

This instruction is not supported. Consider programming with other SFC related instructions. 

 

CSP(221) 

CSP(510) 

The data type of operand is changed from BCD to BIN. For a constant, the # mark is converted to & 
mark. To use word data, change the data type of word from BCD to BIN.   

Same as CV/CVM1 

CSPN(222) 

CSPN(511) 

The data type of operand is changed from BCD to BIN. For a constant, the # mark is    converted to 
& mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

CNR(236) 

CNR(545) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

It might be different.   

PID(270) 

PID(190) 

The data specification of the operand is different. Refer to the 

SYSMAC CS/CS/NSJ Series 

INSTRUCTIONS REFERENCE MANUAL (Cat No. W474

), and correct the data. 

Same as CV/CVM1 

RD2(280) 

None 

This instruction is not supported. Consider programming with the IORD instruction.   
The data of the Special I/O Unit is reflected directly in the I/O memory of PLC. Please refer to the 
operation manual of the Special I/O Unit that you use. 

 

WR2(281) 

None 

This instruction is not supported. Consider programming with the IOWR instruction.   
The data that is written to the I/O memory of PLC is directly reflected to the Special I/O Unit.   
Please refer to the operation manual of the Special I/O Unit that you use. 

 

TST(350) 

TST(350) 

The data type of the 2nd operand is changed from BCD to BIN. For a constant, the # mark is 
converted to & mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

TSTN(351) 

TSTN(351) 

The data type of the 2nd operand is changed from BCD to BIN. For a constant, the # mark is 
converted to & mark. To use word data, change the data type of word from BCD to BIN. 

Same as CV/CVM1 

 

13 

Summary of Contents for CV/CVM1

































Reviews:

No comments

Brands by name

Popular brands

Load more brands