background image

Regulatory Compliances

Safety: 

UL 60950-1,  

UL-62368-1,  

IEC 60950-1:2005+A1 :2009,  

IEC 62368:2014/A11:2017,  

EN 60950-1: 2006+A11:2009+A1:2010+A12:2011 

+A2:2013,  

CAN/CSA C22.2 No. 60950-1,  

CAN/CSA C22.2 No. 62368-1-14,  

CE Mark

EMC: 

EN 55032/EN 55024 CE Emissions/Immunity,  

IEC 61000-6-4 Industrial Emissions,  

IEC 61000-6-2 Industrial Immunity

EMI: 

CISPR 32,  

FCC 47 Part 15 Subpart B Class A

EMS: 

IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV,  

IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10V/m,  

IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV,  

IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV,  

IEC 61000-4-6 CS: Signal: 10 V,  

IEC 61000-4-8 (Magnetic Field),  

IEC 61000-4-11 (General Immunity in Industrial 

Environments )

IP Rating: 

IP40 Protection

Customer Support Information

If you encounter problems while installing this product, contact Omnitron Technical 

Support:

Phone:   

(949) 250-6510

Fax: 

 

(949) 250-6514

Address:  

Omnitron Systems Technology, Inc.

  38 

Tesla

 

 

Irvine, CA 92618, USA

Email:  

[email protected]

URL:  

www.omnitron-systems.com

040-03200-001CD   7/20

Page 20

Page 19

Summary of Contents for RuggedNet GHPoE/Si











Reviews: