omnikine K11 User Manual Download Page 28

Page: 28 / 42

9. Function description

(1) Function description

①

Once the car engine started, K11 is provided with power and red and blue LEDs are on.



Make sure that K11 is connected to the cigar jack via the provided power cable.

②

After booting, K11 starts operating with the recorded message “Hello. Please fasten your seat belt. Voice

instruction starts.”

③

Use the remote control to turn K11 on or off once power is supplied. Or you can unplug the power cable

from the product.

(2) Motion detection while the car is parked

①

This surveillance mode automatically starts when the car stands still for 7 minutes.

②

This surveillance function automatically changes into a normal mode(constant recording/manual recording/event
recording) once the car moves again.

③

During this mode, video images for 20 seconds both before and after a detection are recorded and stored in the

“Motion” folder. Recording time can be reset through the remote control.

④

During the surveillance mode, constant/manual/event recording doesn’t work.

⑤

To use this motion detection function, K11 must be connected to constant power supply.

Note. For a constant power cable and its connection, ask advice from a store near you. Car battery discharge
due to constant power supply to this product shall not be the responsibility of the manufacturer.

Summary of Contents for K11











































Search results

Summary of Contents for K11

Reviews:

Related manuals for K11

Brands by name

Popular brands

omnikine K11, User Manual

Search results

Summary of Contents for K11

Reviews:

Related manuals for K11

Brands by name

Popular brands