background image

Section 1: Introduction

This quick start guide is designed to start or verify the correct operation of

Datalog X-PRO

devices. These devices can measure multiple variables by connecting up to 3 different
external sensors, and then send the collected information from the devices to the
Centriomega® IoT remote monitoring platform.

To follow this guide you will need:

Datalog X-PRO 2.0

.

Magnet (provided by the manufacturer).

A device enabled for internet navigation (PC, Tablet, Smartphone, etc.).

Sensors connected to the

Datalog X-PRO

(optional).

This guide is designed for trained personnel. Read it entirely and carefully before installing
and setting up the product.

The procedures and instructions in this manual may require special
precautions to ensure the safety of the personnel performing the
operations. The information that raises potential safety issues is indicated
by a warning symbol. Refer to the safety messages listed at the beginning
of each section before performing an operation preceded by this symbol.

1.1 Product recycling and disposal

Recycling of device components and packaging should be taken into consideration and
disposed of in accordance with local and national legislation/regulations.

1.2 Storage and transport

The

Datalog X-PRO

is protected by a special packaging during transport and is guaranteed

to handle normal loads during transport.

omicroniot.com

7

June

2023

Summary of Contents for DATALOG X-PRO 2.0




















Reviews: