background image

04

®

Introduction

The LVCN Series are capacitance switches ideal for High/Low level detection for
liquid, solids, granular materials and pastes. These units can also detect level
without being in contact with the product through a sight glass. Unlike other
capacitance probes, the LVCN6000/7000 can detect conductive, non-conductive or
low dielectric materials with extremely accurate performance without requiring an
external reference or installation in a metal vessel.

The sensor operates in a manner that is similar to a simple capacitor. A high
frequency oscillator is located within the tip of the probe. When the tip of the probe
comes in contact with the medium, the frequency of the oscillation reaches a preset
point and the detection circuit signals the switch to change state.

Technology

Both models can be made with cable or rod rigid stainless steel giving more flexibility
to complex applications.

Features

No Moving Parts – Rugged Construction

Highly customizable:

POM (Polyoxymethylene), PTFE or PVC Sensing Tip

Available in DC or Universal Power Supply versions

Almost completely immune from build-up, coating media aggressive products

Easily applied in a wide range of applications/industries such as: water, oils,
corrosives, solids, powders, grains, conductive as well as non-conductive medias.

Extended Lengths with both Rigid 316 rod or Cable

Threaded, Flange or Sanitary Process Connections

LVCN6000/7000

Capacitive Point

Level Detection

Summary of Contents for LVCN6000 series

















Reviews: