The KeyCounter system will stay in Valet Mode until it is removed from Valet Mode.
To remove the system from Valet Mode, turn the ignition switch on, then press and
hold the Valet/Override Switch. The Status Light will briefly illuminate Orange, and
then go out. Normal operation will now resume: turning off the ignition switch results
in the Status Light illuminating solid Orange for 20 seconds indicating impending
engagement, then changing to flashing Red indicating that the starter is immobilized.
While the Status Light is solid Green the vehicle can still be started. Once it changes
to flashing Red, the vehicle cannot be started.
How to Program KeyCounter
TM
Key Fob Discs
Each KeyCounter system comes from the factory with two key fob discs. The
Black disc is for "Daily Use", and the Red disc, which is a special disc. The Red disc
is used for "Programming", but in an emergency can be used in place of the Daily Use
disc. As the Red disc is essential to programming the KeyCounter, it should
be kept in a secure place. If the original Red key fob is lost, only by returning the
control module to the factory can it be re-configured for programming.
KeyCounter can have up to four Black Daily Use discs programmed to operate it,
in addition to the one Red Programming disc. Additional Black Daily Use discs are
readily available, and adding extra or replacement discs is not difficult. Before
beginning programming, have the Red Programming disc at hand along with all Black
Daily Use discs which are to operate the system.
Page - 9
Some important things note to before beginning the programming procedure:
-
When additional Daily Use discs are added, any original disc(s) must also be
reprogrammed. Have all discs at hand, but away from steering column (in which
the KeyCounter's antenna is typically mounted; see note on next page).
-
Before starting, temporarily remove the Black Daily Use disc from the ignition key,
or use an extra key that does not have a disc attached. When the ignition switch
is turned on in step 2, a disc must not be close to the antenna.
-
Once programming has started, each successive step must be performed within
10 seconds of the previous step.
Programming procedure:
1) While the system is in an armed state (flashing Red Status Light), press and hold
the Valet/Override Switch; the Status Light changes to flashing Green.
2) Turn the ignition switch "on"; the Status Light changes to solid Red. Now release
the Valet/Override Switch.
3) Present the Red Programming disc to the antenna; the Status Light changes to
solid Orange.
4) Turn the ignition switch off; the Status Light changes to solid Red.
5) Again present the Red Programming disc to the antenna; the Status Light will go
out momentarily to indicate the disc's code is retained as the Programming disc.
The Status Light returns to solid Red.
6) Now present the first Black Daily Use to the antenna; the Status Light will
momentarily go out, then return to solid Red.
7) Repeat the previous step for each additional Black Daily Use disc.
After 10 seconds of no further disc presentations, the Status Light will change from
solid Red to solid Orange, which indicates the exit from programming mode and the
start of the normal engagement process. If all five code slots are filled, i.e.- one Red
disc and 5 Black discs, the Status Light's change from Red to Orange will occur as
soon as the fifth disc is presented.
Note:
The KeyCounter system has a special antenna which is designed to be mounted
behind the steering column trim panel, below the ignition switch. If the vehicle's
steering column structure allows optimal antenna placement, when the transponder
disc is placed within approximately three inches of the antenna, the radio transmis-
sions between the disc and control module are made and the vehicle is allowed to start.
If the door circuit wire is connected, the radio transmissions will occur as the key is
being inserted into the switch.
Page - 11
Page - 10
Installation
The KeyCounter
TM
system includes the following:
q
The KeyCounter Control Module.
q
Two transponder discs: a Red Programming disc and a Black Daily Use disc.
q
A main wiring harness, with Starter Interrupt socket and relay.
q
A circular transmit/receive antenna.
q
A two-color Status Light.
q
A Valet/Override Switch.
q
A no-drill mounting combination holder for the previous two items.
q
This Owner's Manual and installation instructions manual. After installation and
testing, please place this manual in a conspicuous location within the vehicle.
Due to the sophisticated computerization and the presence of air
bag safety systems, all contemporary vehicles present many hazards to
the installer. Persons lacking proper training and experience can
not only damage the vehicle but suffer serious personal injury.
The KeyCounter
TM
is designed for professional installation!
Page - 12
