background image

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of

one (1) year

from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will

extend  the  warranty  period  for 

four  (4)  additional  years

if  the  warranty  card  enclosed  with  each  instrument  is

returned to OMEGA.

If  the  unit  should  malfunction,  it  must  be  returned  to  the  factory  for  evaluation.  OMEGA’s  Customer  Service
Department  will  issue  an Authorized  Return  (AR)  number  immediately  upon  phone  or  written  request.  Upon
examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s
WARRANTY does  not  apply  to  defects  resulting  from  any  action  of  the  purchaser,  including  but  not  limited  to
mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having
been  damaged  as  a  result  of  excessive  corrosion;  or  current,  heat,  moisture  or  vibration;  improper  specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components which wear are not
warranted, including but not limited to contact points, fuses, and triacs.

OMEGA is  pleased  to  offer  suggestions  on  the  use  of  its  various  products.  However,  OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from
the  use  of  its  products  in  accordance  with  information  provided  by  OMEGA,  either  verbal  or  written.
OMEGA warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA
MAKES  NO  OTHER  WARRANTIES  OR  REPRESENTATIONS  OF  ANY KIND  WHATSOEVER,  EXPRESS  OR
IMPLIED,  EXCEPT  THAT  OF  TITLE,  AND  ALL IMPLIED  WARRANTIES  INCLUDING  ANY WARRANTY OF
MERCHANTABILITY AND  FITNESS  FOR  A PARTICULAR  PURPOSE  ARE  HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability
of  OMEGA with  respect  to  this  order,  whether  based  on  contract,  warranty,  negligence,  indemnification,
strict  liability  or  otherwise,  shall  not  exceed  the  purchase  price  of  the  component  upon  which  liability  is
based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS:  Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component”  under  10  CFR  21  (NRC),  used  in  or  with  any  nuclear  installation  or  activity;  or  (2)  in  medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity,
medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth
in  our  basic  WARRANTY / DISCLAIMER  language,  and,  additionally,  purchaser  will  indemnify  OMEGA and
hold  OMEGA harmless  from  any  liability  or  damage  whatsoever  arising  out  of  the  use  of  the  Product(s)  in
such a manner.

RETURN REQUESTS/INQUIRIES

Direct  all  warranty  and  repair  requests/inquiries  to  the  OMEGA Customer  Service  Department.  BEFORE
RETURNING ANY PRODUCT(S)  TO  OMEGA,  PURCHASER  MUST OBTAIN AN AUTHORIZED  RETURN
(AR)  NUMBER  FROM  OMEGA’S  CUSTOMER  SERVICE  DEPARTMENT (IN  ORDER  TO AVOID
PROCESSING  DELAYS).  The  assigned AR  number  should  then  be  marked  on  the  outside  of  the  return
package and on any correspondence.
The  purchaser  is  responsible  for  shipping  charges,  freight,  insurance  and  proper  packaging  to  prevent
breakage in transit.  

FOR WARRANTY RETURNS, please have the 
following information available BEFORE 
contacting OMEGA:
1. Purchase Order number under which the product 

was PURCHASED,

2. Model and serial number of the product under

warranty, and

3. Repair instructions and/or specific problems 

relative to the product.

FOR NON-WARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1.  Purchase Order number to cover the COST

of the repair,

2. Model and serial number of product, and
3. Repair instructions and/or specific problems 

relative to the product.

OMEGA’s  policy  is  to  make  running  changes,  not  model  changes,  whenever  an  improvement  is  possible.  This  affords  our
customers the latest in technology and engineering.

© Copyright 2004 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of
OMEGA ENGINEERING, INC.

TRADEMARK NOTICE: 

®

,

omega.com

®

,

, and  ™ are Trademarks of OMEGA ENGINEERING, INC.

PATENT  NOTICE: 

This  product  is  covered  by  one  or  more  of  the  following  patents:  U.S.  Pat.  No.  Des.  336,895;  5,274,577;

6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2. Other US and International Patents pending or applied
for.

®

Summary of Contents for ILD24-UTP








































































Reviews: