Page - 12
Step 1.
Enter the vehicle normally, but be prepared for system to activate upon
opening the door.
Step 2.
Using your key, turn "on" the ignition. Be prepared to perform the
following Step before 5 seconds expires.
Step 3.
Within 5 seconds, press and release the Easy Valet
TM
Switch. The system
will immediately disarm.
Once the activated system has been overridden, if Valet Mode is desired, holding the Easy Valet
TM
Switch depressed for two seconds will place the system into Valet Mode.
The E-3000
ATV
Remote Keyless Entry System with Anti-Theft Security System includes a Red
LED Status Light* to inform you of the system's operational condition. These are the conditions of
the LED Status Light:
LED Off ...................................................................... Ignition switch is "On". Also, the system
is "at rest", indicating that no automatic
features (which may have been programmed
to operate) will occur.
LED On Solid Red ..................................................... System is in "Valet Mode".
L E D Status Light
* LED is the abbreviation for Light Emitting Diode - which is defined in the Glossary.
Page - 13
LED Flashing Rapidly ................................................ System has been programmed to automati-
cally arm itself.
LED Flashing Slowly ................................................. System is armed. This will occur whenever
the transmitter is used to lock the doors.
The System may also be programmed to arm
automatically.
LED Flashes 1 To 4 Times After Ignition "On" ........ Number of transmitters stored in the system.
These four indicators are part of the Auto-
matic Transmitter Verification
TM
feature.
LED Flashing 1X & Pause While
Armed, And After Disarming ..................................... System was activated by the optional Current
Sensing feature*.
LED Flashing 2X & Pause
Armed, And After Disarming ..................................... System was activated by the trunk (or rear
hatch) or hood being opened*.
LED Flashing 3X & Pause
Armed, And After Disarming ..................................... System was activated by a door being
opened*.
LED Flashing 4X & Pause
Armed, And After Disarming ..................................... System was activated by an optional sensor*.
Continued Next Page
Page - 14
LED Flashing 5X & Pause
While The System Is Armed ...................................... The Starter Disable circuit has automatically
engaged without the system being armed*.
(This feature must be optionally programmed)
* These indicators are the Zone Violation feature. Unlike the four horn honks and light flashes upon disarming
if the system has been activated and reset automatically, a Zone Violation, as a diagnostic aid, operates without
requiring that the system automatically reset itself.
The E-3000
ATV
includes flashing light and horn honk confirmation. These features provide a visual
and audible indication that the Executive System received the signal from your transmitter. Flashing
Light Confirmation activates both the parking lights and the interior dome lights simultaneously. Also,
if desired, the system's horn honk output may be configured to sound an optional electronic siren.
Standard Confirmation Operations
One Light Flash & One Horn Honk ........................... The has armed and locked the doors.
Lights Illuminate For
30 Seconds & Two Horn Honks ................................ The system has disarmed and unlocked the
doors.
Two Light Flashes & Two Horn Honks ..................... The system has just entered Valet Mode.
Flashing Light & Horn Confirmation
Page - 15
Lights Flash 3 Times & Three Horn Honks ............... The system is being armed with protected
circuit in an activated state.
Lights Flash 4 Times Before Illuminating
30 Seconds & Four Horn Honks ................................ The system has disarmed and was activated
and reset before being disarmed.
Two Horn Honks & No Lights Activity
When The Ignition Switch Is Turned "Off" ............... The system is reminding you that it is in
Valet Mode.
Confirmation Operations With Optional Programmable Features
One Light Flash & No Horn Honk ............................. The system is in the process of automatically
arming or rearming.
Special Confirmation Operations
Horn Honks For Two Seconds
When The Ignition Switch Is Turned "On" ................ The Automatic Transmitter Verification
feature system is alerting you that transmitter
programming activity has occurred within the
last 48 hours.
Silently Operating The System: If desired, the transmitter can temporarily lock and unlock the
vehicles doors without the confirmation horn honks. This is accomplished with both the three button
and four button transmitters by pressing and releasing the button labeled "OPTION", then within three
seconds pressing "LOCK" or "UNLOCK" button. The confirmation honk(s) will be silenced for that
Continued Next Page
