background image

During operator programming in "FUNCTION SELECT"
MODE
, the Main Display is used to:

1. Set the Zone Setpoints
2. Enter Passwords
3. Select Functions
4. Set the Zone Display Time
5. Select the Instrument Model
6. Select Run parameters

During CALIBRATION (Function 78), the Main Display is used
to:

4.4 Temperature/Setpoint Display (Main Display)

During "RUN" MODE, the Main Display is used to monitor zone
temperatures, check setpoints, and indicate ALARM conditions.

21

0 5 2 2

5 1

3

Zone

Run Mode

Temperature

By pressing and holding button              The display will change to

0 5 2 0

5 1

3

Zone
Flashing

Run Mode

Setpoint

1. Set calibration millivolts

3 1.0 5

7 8

Function

Mv

SECTION 5

“RUN” MODE

In the “RUN” Mode, the CN616 controls the temperature under the
program established during the last “SET” Mode. The “RUN” Mode is
entered every time the controller is powered, after a power interruption, or
it can be entered manually from the “SET” Mode, by pushing buttons
 and

     together

“SET” Mode TIME OUT. If the instrument is left unattended for over 2
minutes in the “SET” Mode, the program will switch it back to “RUN”
Mode.
Three “RUN” Modes are available
1. [00]  Standard Control     FN 33   Control Mode (digit 3) = 0
2. [51]  RAMP & SOAK 1  FN 33   Control Mode (digit 3) = 1
3. [52]  RAMP & SOAK 2  FN 33   Control Mode (digit 3) = 2

5.1  PID CONTROL MODE

Each  one of the six zones is treated as a separate controller and  it can run
under any one of the following Modes
1. PID enable

FN 43

2. Proportional Band (PB)

FN 44  -  FN 45 & 46 set  to 0

3. Proportional Band and Reset (PI)  FN 44 & 45   - FN 46 set to 0
4. Proportional Band and Rate (PD)  FN 44 & 46   - FN 45 set to 0
5. Proportional Band Reset and Rate (PID)  FN 44 , 45 & 46
6. Disabled  (OFF)

 FN 31

NOTE!!   The PID setting is common to all zones i.e.:-
it can  not be changed from zone to zone.
The zones can be mixed and set  to either PID or ON-OFF  FN [43]

22

5.2  RAMP & SOAK CONTROL 1
In this Mode each zone will follow the RAMP & SOAK program set in
Section 6: FN 74 & 75 . At the end of the Profile “RUN” the output power
will be switched OFF.
5.3 RAMP AND SOAK CONTROL 2
This Mode is exactly the same as RAMP & SOAK 1 except  that at the end
of the Profile “RUN” the controller will control the temperature at the setpoint
of the last segment indefinitely.

Summary of Contents for CN616TC1





























Reviews: