background image

vehicular horn, this output pulses for 10 seconds, then pauses for 5 seconds, repeat-
ing this cycle for the duration of the activated alarm period.  When set for use with
the electronic siren, the output is continuous and steady.  When programming, please
note that pressing the remote transmitter's LOCK button sets the pulsed horn, and
pressing the UNLOCK button sets the steady siren.

#22  Loud or Soft Confirmation Chirps: Default Loud.  If the system is config-
ured to use the vehicle's horn, this feature allows a degree of compensation for the
variance which is found in the length of the pulse required to chirp the vehicle's horn
in a satisfactory manner.  When programming, please note that pressing the remote
transmitter's LOCK button sets the chirp loud, and pressing the UNLOCK button
sets the chirp soft.  This feature is only available for use when the previous feature is
programmed for the "Pulsed Horn" setting.

#23  Total Closure Lock Output: Default OFF.  If the vehicle is has an existing
total closure feature, this programmable feature allows the installer the option of
interfacing the system to operate this feature.  Typically, this option would close all
windows and the sunroof, in addition to locking the doors, when arming the system.
Consult with the installer on this option, as the vehicle must be properly equipped to
utilize this Feature.

#24  Alarm Functions Bypass: Default OFF.  This feature converts the system into
a Remote Keyless Entry System only by eliminating all antitheft alarm-oriented

Page - 40

Page - 41

operations and features.  When this feature is programmed on, the system has
remote keyless entry operation only.

#25  Ignition-Activated Anti-Carjacking Protection: Default OFF.  Your system
offers two separate forms of anti-carjacking protection: this feature and the following
feature.  When this feature is utilized, you must press the valet

 

switch once within 60

seconds after turning the ignition switch "on" and starting the vehicle; otherwise the
anti-carjacking operation will occur.

If this is not done within this period, the system will begin chirping the siren 53

seconds after the ignition was turned "on".  These chirps are to warn you that the
anti-carjacking protection is about to engage; pressing the valet switch before the 60
seconds expires will stop the anti-carjacking protection feature. Once starting, the
chirping will last for 7 seconds.  Unless the anti-carjacking feature is cancelled as
described, once 60 seconds has passed from the time the ignition was turned "on",
the siren will start sounding fully, and the parking lights will begin flashing.  Thirty
seconds after this occurs, or if the ignition is turned "off", the starter interrupt circuit
will also activate.

Once the Anti-Carjacking is fully engaged, sounding the siren and flashing the

lights, the only way to disengage it is to turn the ignition "off", then "on" again, and
then press the valet switch within 5 seconds.

#26  Door-Activated Anti-Carjacking Protection: Default OFF.  This feature's
operation is the same as described in the previous section, with the exception of

being activated by the opening of a door while the ignition switch is "on".  Once the
engine is running, if a door is opened the valet switch must be pressed before 60
seconds expire.  Otherwise, the operation of this feature is identical to that described
for "Ignition Activated Anti-Carjacking Protection".  This and the previous feature are
independently programmable, and one or both may be programmed to operate.

#27  Open Door Warning Upon Arming: Default OFF.  When this feature is
programmed to operate, if one of the vehicle's doors is open when the system is armed
using the remote transmitter, the siren will

chirp 3 times instead of once when

arming the system with the transmitter.

#28  PANIC Button Operates Panic / Additional Output: Default Panic.  This
feature changes the remote transmitter's operation of the panic feature and the
additional output.  When this feature is used, pressing the transmitter's PANIC button
for 2 seconds will operate the additional output.  The remote panic feature can still be
operated, but changes to pressing the LOCK button for 2 seconds to activate it.  Once
activated, pressing the LOCK, UNLOCK or PANIC button will deactivate the remote
panic feature.  Deactivating the remote panic feature is the same regardless of whether
the PANIC or LOCK button is programmed to activate it.  The remote panic feature's
operation is explained on pages 14-15.

Page - 42

#29 Remote Start Engine Run Time 10 Or 20 Minutes: Default 10 Minutes.  This
Feature sets the period of time that the engine will run after being remotely started.
If the engine is not stopped by transmitter or a safety circuit violation, the engine will
automatically stop upon the expiration of the selected time period.

#30 Gasoline Or Diesel Engine: Default Gasoline.  This Feature changes the
system's timing of the ignition and starter output sequence for remotely starting
vehicles with a diesel engine.

Page - 43

Summary of Contents for C-4SRS












Reviews: