![background image](http://html1.mh-extra.com/html/omca/930/930_use-and-maintenance-manual_3912903024.webp)
5
MANUTENZIONE
E REGOLAZIONI
MAINTENANCE
AND ADJUSTMENT
24
OMCA S.r.l
-
Via Curiel, 6 - 42025 - Cavriago (RE) - ITALY
Telefono:
+39 0522 943502 / +39 0522 943503 -
Website
: www.omcasrl.it -
5.2 PULIZIA
ATTENTION:
BEFORE EXECUTIng CLEAnIng OPERATIOnS, BE SURE THAT
THE gEnERAL SwITCH IS On POSITIOn
OFF
(
0
), MOREOVER
DISCOnnECT THE PLUg FROM THE SOCKET.
ATTENZIONE:
PRIMA DI ESEgUIRE OPERAzIOnI DI PULIzIA ASSICURARSI CHE
L’InTERRUTTORE gEnERALE SIA In POSIzIOnE
OFF
(
0
) InOLTRE
DISInSERIRE LA SPInA DALLA PRESA DI CORREnTE.
Pulire il piano di lavoro tramite aria compressa, la pressione dell’aria
deve essere moderata.
nel caso vi sia la necessita di pulire il piano di lavoro es. da
grasso, utilizzare una soluzione detergente che non sia nociva per il
manutentore e che non danneggi la macchina (
leggere attentamente
le indicazioni riportate sul prodotto
).
non spruzzare prodotti liquidi su parti elettriche.
5.3 CAUSE E RIMEDI
Sostituzione batteria indicatore di posizione:
Lo strumento è alimentato con una batteria al litio formato
1/2 AA
da
3,6V
che assicura un funzionamento di circa 4 anni. Quando è
necessario sostituire la batteria si attiva l’indicatore di batteria scarica.
Per accedere al vano portapila, occorre togliere il coperchietto sul
frontale facendo leva con un cacciavite a lama piatta sui due incavi posti
a lato dello strumento. Tolto il coperchio estrarre la pila e sostituirla con
la nuova rispettando la polarità: il polo positivo deve trovarsi dal lato
del tasto
RESET/ENTER
. Lo strumento è protetto contro l’inversione di
polarità e in caso di errato inserimento della pila non si accende e non
subisce alcun danno. Togliendo la batteria lo strumento si spegne entro
qualche secondo, in questa fase si raccomanda di non ruotare l’albero
cavo pena la perdita della corretta quota visualizzata. non appena la
nuova pila viene inserita, lo strumento si accende con la quota sul
display pari a quella che aveva al momento di spegnersi e se non si
è mosso l’albero la quota sarà corretta. nel caso in cui si dovesse
muovere l’albero cavo mentre lo strumento è spento, per ripristinare
la corretta misura occorre ripetere la procedura di taratura della quota.
5.4 SMALTIMENTO
Lo smaltimento della macchina, scarti di lavorazione o eventuali
componenti sostituiti, devono essere smaltiti rispettando le normative
vigenti nel paese d’installazione della macchina.
DURAnTE LA PULIzIA DELLA MACCHInA DEVOnO ESSERE
InDOSSATE LE SEgUEnTI PROTEzIOnI, PER LA SICUREzzA DEL
MAnUTEnTORE:
DURIng THE CLEAnIng OF THE MACHInE, THE FOLLOwIng PROTECTIOn
MUST BE wEAR, FOR THE OPERATOR SAFETY:
Occhiali
glasses
guanti
gloves
Scarpe antinfortunistiche
accident-prevention shoes
Cleaning the work bench by using compressed air, the air pressure
must be moderated.
In case it is necessary to clean the work bench from grease, use a
cleaning product that is not noxious for the operator and not damage
the machine (
read carefully the indications listed on the product
).
Do not spray fluid products on electrical parts.
5.3 CAUSES AND REMEDIES
Replacing battery for position indicator:
The instrument is supplied with a
1/2 AA 3,6V
lithium battery, which
assures a typical functioning of approximately 4 years.
when the battery runs down, an icon appears on the display.
To enter into the battery-holder it is necessary to remove the front
cover by carefully inserting a flat screwdriver on the sides. After
taking off the cover, pull the battery out and substitute it with a new
one, paying attention to the polarity: the positive pole must face the
side of the
ENTER/RESET
button. The instrument is protected against
inversion of polarity and wrong insertion, and in this case will not
switch on. Removing the battery from the instrument switches it off
after a few seconds: at this point do not rotate the hollow shaft to
avoid losing the correct displayed value. As soon as the battery is
fitted, the instrument switches on with the same value on the display
which was present at the moment when it was switched off. If the
shaft has not be moved, the displayed value will be correct.
In case the shaft moved when the instrument was off, to re-establish
the correct measure it is necessary to repeat the adjustment process.
5.4 DISPOSAL
The disposal of the machine, processing waste or eventual replaced
components, must be disposed respecting the rules in force in the
Country where the machine is installed.
5.2 CLEANINg
Summary of Contents for 930
Page 26: ......