![background image](http://html1.mh-extra.com/html/omca/930/930_use-and-maintenance-manual_3912903011.webp)
4
UTILIZZO
USE
11
OMCA S.r.l
-
Via Curiel, 6 - 42025 - Cavriago (RE) - ITALY
Phone:
+39 0522 943502 / +39 0522 943503 -
Website
: www.omcasrl.it -
C
-
Interruttore principale
: Permette di sezionare la macchina dalla
alimentazione elettrica esterna.
D
-
Spia scatto termica
: Si accende quando c’è un sovraccarico al
motore. Quando si accende occorre dapprima rimuovere la causa
che ha portato al sovraccarico e, successivamente, riarmare la
termica all’interno del quadro elettrico premendo sul pulsante nero
del salvamotore che è intervenuto, posizionandolo su
ON (I)
come
indicato in (
Fig.4.1 Pos. 1
).
C
-
Main switch
:
it allows the cut-out of the machine from the external
current supply.
D
-
Thermal light release
:
It switches on when
the motor is
overloaded the thermal pilot switched on. when it happens you
have to remove the cause of the problem, and then restart the
thermal inside the control board by pushing the black button of the
motor protection. By turning on the
ON (I)
position as showed on
(
Pic.4.1 Pos. 1
).
ATTENTION:
BEFORE STARTIng MAInTEnAnCE, BE SURE THAT THE
gEnERAL SwITCH IS On POSITIOn
OFF
(
0
), MOREOVER
DISCOnnECT THE PLUg FROM THE SOCKET.
OnLY SPECIALIzED OPERATORS CAn EXECUTE THE OPERATIOnS OF
MAInTEnAnCE OF THE MACHInE, RESPECTIng ALL THE PROCEDURE
ACCORDIng TO THE SAFETY AnD HEALTH LAwS In FORCE.
ATTENZIONE:
PRIMA DI ESEgUIRE OPERAzIOnI DI MAnUTEnzIOnE
ASSICURARSI CHE L’InTERRUTTORE gEnERALE SIA In
POSIzIOnE
OFF
(
0
) InOLTRE DISInSERIRE LA SPInA DALLA
PRESA DI CORREnTE.
gLI InTERVEnTI DI MAnUTEnzIOnE DEVOnO ESSERE SVOLTI DA
PERSOnALE QUALIFICATO E ADDESTRATO, nEL PIEnO RISPETTO
DELLE nORME DI SICUREzzA E SALUTE VIgEnTI.
E
-
Pulsante di start
: Permette di accendere la macchina. Va premuto
dopo aver ruotato su
ON (I)
l’interruttore principale, oppure dopo
aver riarmato il pulsante di emergenza.
F
-
Spia
“
tensione
”: La spia è accesa quando la macchina è connessa
all’alimentazione elettrica esterna e quando l’interruttore principale
è su
ON (I)
.
H
-
Albero mandrino - blocco fresa
.
I
-
Perno sblocco regolazione smusso
: Deve essere allentato con la
chiave di 13 fornita in dotazione, solo quando si deve modificare la
dimensione dello smusso, quando la macchina lavora deve essere
sempre bloccata.
L
-
Pulsante rosso di stop
: Serve per arrestare la macchina,
premendolo si ferma prima l’avanzamento e dopo pochi secondi
la rotazione della fresa.
M
-
Volantino regolazione altezza
: Serve per allineare in altezza la
macchina con la lamiera, quando si lavora in modalità da banco.
Ruotando in senso orario si alza la macchina, mentre si abbassa
ruotando in senso antiorario.
L’escursione permessa è di
200 mm in verticale
.
N
-
Cavo di alimentazione
: Serve per alimentare la macchina ed
è importante che venga protetto da urti e da pesi che possano
danneggiarne il funzionamento.
O
-
Manopola regolazione velocità di avanzamento
: Tale comando
serve per regolare la velocità di avanzamento sulla base dei
vari materiali da lavorare e della dimensione dello smusso, per
garantire un ottimo grado di finitura.
La velocità di avanzamento può variare da
0 a 1,2 m/min
.
E
-
Start button
:
it makes the machine start. Push it after rotating the
main switch on the
ON (I)
, or after reset the emergency button.
F
-
Light “voltage”
:
The light is on when the machine is connected to
the external power supply and also when the main switch is
ON (I)
.
H
-
Spindle shaft – cutter locking.
I -
Chamfer adjustment unlocking pin
:
it must be loosen (with
the suitable key 13 supplied with the equipment) only when it is
necessary to modify the chamfer dimension; when the machine
is working, it must be always locked.
L
-
Red stop button
: It allows to stop the machine, by pushing it, the
feed stops firstly and, few seconds later, the milling-cutter rotation.
M
-
Height adjustment handwheel
: It is for aligning the height of the
machine with the sheet, when works in bench mode.
Turning clockwise the machine moves up, turning counterclockwise
it moves down.
The range permitted is
200 mm vertically
.
N
-
Power cable
:
it supplies power to the machines, for this reason
you must pay attention and protect it from bumps that could
damage it.
O
-
Feed speed adjustment handwheel
:
it is used for the adjustment
of feed speed in according to the various material and the chamfer
entity, in order to grant an excellent finishing.
The feed speed can vary from
0 to 1,2 m./min
.
Summary of Contents for 930
Page 26: ......