Olympus MV-1 Frequently Asked Questions Manual Download Page 4 | Manualshive

Page: 4 / 18

Olympus MV-1 Frequently Asked Questions Manual Download Page 4

MV-1/MV-2 Endoscope Disinfectors

Frequently

Asked

Questions

09FQ0015 4/18

Two Corporate Center Drive, Melville, NY 11747

Copyright 2001, Olympus America Inc.

Copyright 2001 Olympus America Inc. This document and the contents contained herewith remain the property of Olympus America Inc. Reproduction of this document or any part

thereof by any means (electronic or otherwise) without the expressed written consent of Olympus America Inc. is strictly prohibited. Only printed copies with "Controlled Document -- Do

Not Copy" stamped in red are considered controlled copies. All other printed copies are considered Uncontrolled and may not contain the latest document revisions.

Compatible Components

The MV-1/MV-2 Endoscope Disinfectors are compatible with the following components.

Mobile Cart

•

CLM-1005

LCG transfer pump

•

CLM-1087

Two Stage Water Filtration System

•

CLM-1076

MV-1 Software Upgrade Kit*

•

MV-1

(5001)

MV-2 Software Upgrade Kit*

•

MV-2

(5002)

*The software upgrade kit must be installed if Cidex® OPA is utilized as the disinfectant.

«
...
2
3
4
5
6
...
»

Summary of Contents for MV-1



















Reviews:

No comments