Olympus BXC-CBB Instructions Manual Download

Page: 5 / 41

Configuration of instruction manuals

Read all the instruction manuals supplied with the units you purchased.

The following instruction manuals are prepared for the units to be used with this product.

Manual names

Main contents

BXC-CBB

Safety manual

Safety precautions

BXC-CBB

Hardware manual

Safety precautions, specifications and assembly method

BXC-CBB

Application manual

Advanced BXC-FSU Usage. For details, contact us.

BXC-CBB

Command reference manual

How to use RS-232C communication commands. For details, contact us.

Intended use

This product is designed to observe magnified images of specimens in industrial applications.

Appropriate samples include semiconductors, electrical components, molded parts or mechanical parts.

Industrial applications include observation, inspection or measurements.

Do not use this product for any purpose other than its intended use.

Introduction

1. Introduction

Summary of Contents for BXC-CBB










































Search results

Summary of Contents for BXC-CBB

Reviews:

Related manuals for BXC-CBB

Brands by name

Popular brands

Olympus BXC-CBB, Instructions Manual

Search results

Summary of Contents for BXC-CBB

Reviews:

Related manuals for BXC-CBB

Brands by name

Popular brands