background image

Complete Teardown, Cleaning/Lubrication, and Reassembly of the Olympus BH2-CH Substage Assembly   

Revision 1      Page 10 of 26 

 

Figure 16 – Remove screws and washers securing rack 

Remove the loose condenser-height rack from the face 
of the dovetail slide (se

Figure 17

). 

 

Figure 17 – Remove the condenser-height rack 

Look  for  a  brass  shim  either  on  the  back  of  the 
condenser-height  rack  or  on  the  face  of  the  dovetail 
slide (se

Figure 18

). 

 

Figure 18 – Brass shim for the condenser-height rack 

Remove the brass shim from the back of the condenser-
height  rack  or  from  the  face  of  the  dovetail  slide, 
whichever is applicable (se

Figure 19

).   

 

Figure 19 – Remove brass shim for condenser-height rack 

Disassemble the Condenser-Height Stop 

Hold  the  M5x12  condenser-height  stop  pin  down  with 
your finger, and use a 1.5mm Allen wrench or driver to 
loosen the M3x4 set screw holding the stop pin in place.  
While holding your finger on top of the stop pin, allow 
the stop pin to rise in order to alleviate the compression 
on the internal stop spring (see 

Figure 20).

 

 

Figure 20 – Loosen set screw while holding the stop pin 

Remove  the  M5x12  stop  pin  from  the  bore  in  the 
condenser slide (see 

Figure 21

). 

 

Figure 21 – Remove the loose stop pin from the bore 

Remove  the  stop-pin  spring  from  the  bore  in  the 
condenser slide (see 

Figure 22

). 

Summary of Contents for BH2-CH Substage



























Reviews: