background image

Complete Teardown, Cleaning/Lubrication, and Reassembly of the Olympus BH2-CH Substage Assembly   

Revision 1      Page 25 of 26 

 

Figure 106 – Reinstall the condenser-slide stop screw 

Adjust the Condenser-Height Stop 

The  purpose  of  the  condenser-height  stop  on  the 
BH2-CH substage assembly is to allow the condenser to 
be  raised to the  height  required  to  achieve  the  proper 
setup  for  Köhler  illumination,  yet  prevent  the  upper 
lens  element  from  contacting  the  bottom  of  the  glass 
specimen slide.  The height stop can be adjusted by first 
mounting  the  condenser  into  the  BH2-CH  substage 
assembly,  and  then  adjusting  the  condenser-height 
knob until the stop pin in the condenser slide either hits 
the  stop  (see 

Figure  107

,  shown  with  the  condenser 

removed  for  clarity),  or  reaches  the  desired  maximum 
height (i.e., just short of the point where the upper lens 
element  of  the  condenser  contacts  the  bottom  of  a 
glass slide sitting on the stage surface).   

 

Figure 107 – The condenser set to maximum height 

If  the  mechanism  reaches  the  stop  at  the  proper 
condenser height, no further adjustment is needed.  If it 
does not, use a 1.5mm Allen wrench or driver to loosen 
the  M3x4  set  screw  securing  the  stop  pin  in  position 
(se

Figure 108

and turn the condenser-height knob to 

set the condenser to the desired maximum height, then 
retighten the set screw to lock the stop pin to this new 
position.  The condenser-height stop should be checked 
anytime  a  different  condenser  is  mounted  into  the 
BH2-CH substage assembly, and should be readjusted if 
necessary to prevent the condenser from contacting the 

bottom  of  the  glass  slide.   

Caution:

  Never  loosen  the 

M3x4 set screw securing the condenser-height stop pin 
(se

Figure  108

)  unless  the  condenser  is  at  or  near  its 

maximum  height  setting,  otherwise  the  spring  in  the 
stop mechanism might eject the stop pin.   

 

Figure 108 – The set screw for the condenser-height stop 

Ready for Service 

The BH2-CH substage assembly is now ready for service 
and can be reinstalled onto the microscope stand. 

 

Original Olympus Documentation 

A  scanned  PDF  of  the 

Olympus  Research  Microscope 

Series  BH2  (BHS)  Repair  Manual 

is  available  for 

download  at  various  microscope-related  hobbyist  sites 
on the internet, and can be found by searching for the 
title in an internet search engine, such as Google. 

 

Figure 109 – Olympus BH2 (BHS) repair manual 

How to Contact the Author 

Please  feel  free  to  direct  any  questions  or  comments 
regarding  this  document  (or  BH-2  microscopes  in 
general)  to  the  author,  at  the  following  email  address: 

[email protected]

 

Summary of Contents for BH2-CH Substage



























Reviews: