Olympia LT-80 Operating Manual Download Page 20 | Manualshive

Page: 20 / 26

background image

◉

in the burner model LT40UH, LT45UH, LT60UH separate burner from the furnace.

then also separate the flange tube, and follow the adove procedure for

replacement.

b) how to disassemble and check nozzle

① separate filter (㉣). clean the filter using kerosene.

② separate the gelical support (㉢) using a screwdriver. clean the groove (㉡) using

kerosene and thin wire. do not use iron wire or needle. otherwise the nozzle hole

may widen.

③ after the nozzle hole is clean, assemble nozzle in the reverse order.

◉

make it fasten it set up.

«
...
18
19
20
21
22
...
»

Summary of Contents for LT-80



























Reviews:

No comments

Related manuals for LT-80

Brand: Fisher & Paykel Pages: 16

Brand: Greenheck Pages: 40

Kromschroder ECOMAX 1

Brand: Elster Pages: 16

Brand: DCS Pages: 90

Brand: Cadac Pages: 7

Brand: Nu-Way Pages: 14

Brand: WarmingTends Pages: 23

Brand: Lamborghini Caloreclima Pages: 84

Brand: Gasmate Pages: 8

BT 250 DSG K Series

Brand: baltur Pages: 90

Professional Series PRO36RBI

Brand: Capital Pages: 2

Brand: Capital Pages: 2

Professional Series PRO32RBI

Brand: Capital Pages: 2

Brand: Riello Pages: 36

Brand: Riello Pages: 60

Brand: Riello Pages: 24

Brand: Riello Pages: 44

Brand: RIELLO BURNES Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands