background image

DIMMING OPTION

When  the  voltage  is  interrupted,  with 
corresponding  press

ing

s  of  the  button,

 

we 

ca

n

  choose 

the  illumination  of  100%,  50%, 

33% 

  or 

turned  off

,  either  to  increase  the 

autonomy time or not to consume 

the 

battery 

power unnecessarily. This option is canceled 
when the

 power 

 network is restored.

LAMP TESTING

The luminaire tests the good condition of the 
lamps  in  emergency  mode  and  warns  the 
user  for  probable  malfunction.  If  a  lamp  is 
found faulty then 
the LAMP FAULT indicator starts to blink. To 
verify  which  lamp  is  faulty  use  the  TEST 
button. If the faulty lamp is replaced then the 
error  is  automatically  restored  and  the 
indicator is turned OFF.

TESTS

Normally  the  illumination  source  and  the 
autonomy  tests  are  programmed  by  the 
control panel and the test results are sent to 
the control panel.

If  the  luminaire  is  not  connected  to  GR-
6500 panel, the following automatic tests 
executed:

 

AUTOMATIC EMERGENCY CIRCUIT TEST

The  unit  automatically  tests  the  emergency 
circuit every 15 days (if the battery and mains 
power  are  connected).  During  this  test  the 
lamps are turned ON for 3 seconds using the 
batteries. In some cases this function might 
not be acceptable (i.e in cinema theaters) so 
the  installer  must  take  this  into  account 
during the installation.

AUTOMATIC DURATION TEST

This  test  is  conducted  every  6  months  by 
simulating a power failure, if the battery and 
mains power supply are connected. The unit 
lights  the  lamps  using  the  charged  battery 
and counts the time until the stated duration. 
If the lamps are ON during the end of the test 
then  the  unit  is  restored  to  its  normal 
operation (lamps OFF and battery charging). 
If the lamps go OFF before the end of the test 
then  the  unit  is  restored  to  its  normal 
operation  but  the  LAMP  FAULT  /  BATT. 
FAULT indicator is lit to show that there is a 
problem with the battery and that the battery 

must  be  replaced.  Let  it  be  noted  that  this 
duration test is also done during every long 
power failure. If the power failure lasts for a 
long time and the luminaire has entered the 
BATTERY CUTOFF mode and the duration 
measured  is  not  correct  then  the  fault 
indicator will light when the power is restored.

ERASING ERRORS

Erasing  errors  is  accomplished  with  a 
prolonged pressing of the TEST button (>5 
sec) when the unit is connected to the mains 
power  supply.  The  fault  indicated  with  the 
indicator  LAMP FAULT / BATT. FAULT will be 
erased. If the cause of the fault has not been 
restored (i.e burned lamp) then the indicator 
will light again. If the fault was caused by a 
low emergency duration and you erase the 
error then this will be indicated again during 
the next duration test after 6 months. In this 
case (for duration errors) it is vital to replace 
the battery before erasing the error (the error 
is  automatically  erased  if  the  mains  power 
and the battery are disconnected).

WARNING

 

!

!!

1.

 Every test, installation or maintenance

    procedure must be done only by qualified
    personnel.

2.

 The unit must be connected to the mains

    power supply using a line fuse rated
    accordingly.

3.

 The replacement of the battery and the

    

light

 

source must be done using parts of

    the same type, by the manufacturer or by
    a competent person.

4.

 If the luminaire must be isolated from the

    mains power supply for more than 2
    months then the batteries must be
    disconnected by removing the battery\
    connectors.

5.

 

I s not allowed to discard batteries in 

t i

to

  c

ommon  trash  bins,  they  must 

b e   d i s c a r d e d   o n l y  

i n   b a t t e r y  

recycling points. Do not incinerate.

Page

 2 

from

 7

92303

7

00

8

_09_00

1

Summary of Contents for GRL-37/90/ADR








Reviews: