background image

1. Install the included mounting accessories to hook the device from the mounting holes (fig. 1)

.

2. 

Unfasten the 4 mounting screws to remove the front plastic cover (fig. 1)

.

3. Make sure that the battery’s cables are connected to the respective poles. Black cable to (-) pole 
    and red cable to (+) pole.
4. Install the included cable gland or the rubber o-ring. Pass through the mains cable and stabilize it
    by fastening the cable gland. Connect the wires to the terminal blocks 

L

 for live wire and

 

Ν

 

for 

    neutral

.

5. 

Refit with care the front plastic cover, by fastening the 4 mounting screws (tightening torque 

    1N

*

m).

NOTE!!  After finishing the installation you must power the luminaire at least for 24 hours for 
battery charging to perform the nominal autonomy. 

INSTALLATION PROCEDURE (For wall mounting only)

Page

 3 

from

 7

92303

7

00

8

_09_00

1

INDICATION LED STATUS (with the mains power supply connected

)

Battery replacement

It can be done only by a competent person and after the mains interruption.

1.

 Follow the step 2 

o

f the installation procedure.

2.

 Disconnect the 

cables

 and remove the old

 

battery.

3.

 Connect the new battery with the same type (step

 3

 of the installation procedure) and place

 

it 

i

n

    

the

 

position

 

of the old one.

4.

 Follow the step 

6

 of the installation procedure

 

and

 

power the device.

POWER / CHARGE

LAMP FAULT / BATT. FAULT

Disconnected battery

 / 

not charging

Normal operation mode

Charged battery

Low emergency duration

 (

replace battery

)

Battery under charge

Lamp fault (Check lamps and replace if needed)

Indicator ON

Indicator Blinking

Indicator OFF

N

4

3

L

TEST

button

Fig

.

 1

POWER
CHARGE
indicator

Mounting holes

LAMP FAULT
BATT. FAULT
indicator

Cover

retaining

 

screws

Summary of Contents for GRL-37/90/ADR








Reviews: