background image

Page

 

10 from

 

10

940813000_09_0

1

2

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The 
period of warranty is specified in the official catalogue of Olympia Electronics and 
also in the technical leaflet, which accompanies each product. This warranty ceases 
to exist if the buyer does not follow the technical instructions included in official 
documents given by Olympia Electronics or if the buyer modifies the goods provided 
or has any repairs or re-setting done by a third party, unless Olympia Electronics has 
fully agreed to them in writing. Products that have been damaged can be returned to 
the premises of our company for repair or replacement, as long as the warranty 
period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and 
to or not charge the buyer depending on the reason of defection. Olympia Electronics 
reserves the right to charge or not the buyer the transportation cost.

HEAD OFFICE

72

nd

 

km

O

.

N

.

R

Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

WARRANTY

WARRANTY

Summary of Contents for BS-812











Reviews: