background image

940813000_09_0

1

2

Page

 

9 from

 

10

230V~

mains

BS-81

4

BS-813

Mains
ground

Yellow-green

wire  (PE)

230V~

mains

(

Previous thermostat installation

)

BS-81

2

230V~

mains

(

Previous thermostat installation

)

To burner

 (

L)

For new installation a third wire for neutral N 
is not required

 (

3 wire connection

)

.

The installation MUST be performed by an 
authorized electrician. Otherwise the
warranty will be invalid.   

Electrical connections

Electrical connections

The installation MUST be 
performed by an 
authorized electrician. 
Otherwise the warranty 
will be invalid.   

For new installation a third wire for neutral N 
is not required

 (

2 wire connection

)

.

The installation MUST be performed by an 
authorized electrician. Otherwise the
warranty will be invalid.   

Neutral blue wire 

(Ν).

 IS NOT CONNECTED

Live Brown wire

 (

L)

Neutral blue wire 

(Ν).

 IS NOT CONNECTED

Live wire

 (L) 

to burner

Live wire

 (L) 

to

 

Boiler

Live Brown wire

 (

L)

Heating element

(2

.

8

kW maximum

)

Blue wire

 (Ν)

Yellow-green

wire (PE)

Brown wire

 (

L)

Neutral blue wire

 (Ν)

Brown wire

 (

L)

Summary of Contents for BS-812











Reviews: