olympia electronics BS-812/A Manual Download Page 9

Page: 9 / 10

Page 9 from 10

230V~

mains

BS-814/A

BS-813/A

Mains
ground

Yellow-green

wire (PE)

230V~

mains

(Previous thermostat installation)

BS-812/A

230V~

mains

(Previous thermostat installation)

To burner (L)

For new installation a third wire for neutral N
is not required (3 wire connection).

The installation MUST be performed by an
authorized electrician. Otherwise the
warranty will be invalid.

Electrical connections

The installation MUST be
performed by an
authorized electrician.
Otherwise the warranty
will be invalid.

For new installation a third wire for neutral N
is not required (2 wire connection).

The installation MUST be performed by an
authorized electrician. Otherwise the
warranty will be invalid.

Neutral blue wire (Ν). IS NOT CONNECTED

Live Brown wire (L)

Neutral blue wire (Ν). IS NOT CONNECTED

Live wire

(L)

to burner

Live wire

(L)

to Boiler

Live Brown wire (L)

Heating element

(2.8kW maximum)

Blue wire (Ν)

Yellow-green

wire (PE)

Brown wire (L)

Neutral blue wire (Ν)

Brown wire (L)

940812001_09_001

Summary of Contents for BS-812/A











Search results

Summary of Contents for BS-812/A

Reviews:

Related manuals for BS-812/A

Brands by name

Popular brands

olympia electronics BS-812/A, Manual

Search results

Summary of Contents for BS-812/A

Reviews:

Related manuals for BS-812/A

Brands by name

Popular brands