background image

Page 10 from 10

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

72nd km. O.N.R. Thessaloniki-Katerini

HEAD OFFICE

[email protected]

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The 
period of warranty is specified in the official catalogue of Olympia Electronics and also in 
the technical leaflet, which accompanies each product. This warranty ceases to exist if 
the buyer does not follow the technical instructions included in official documents given 
by Olympia Electronics or if the buyer modifies the goods provided or has any repairs or 
re-setting done by a third party, unless Olympia Electronics has fully agreed to them in 
writing.  Products  that  have  been  damaged  can  be  returned  to  the  premises  of  our 
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or 
not  charge  the  buyer  depending  on  the  reason  of  defection.  Olympia  Electronics 
reserves the right to charge or not the buyer the transportation cost.

WARRANTY

WARRANTY

940812001_09_001

Summary of Contents for BS-812/A











Reviews: