olympia electronics BS-429/W Quick Installation Manual Download Page 2

Page: 2 / 28

Page 2

921468007_90_005

Contents

1. BEFORE INSTALLATION ................................................................................................. 4

1.1 GENERAL INFORMATION ................................................................................................. 4

1.2 What includes the wireless KIT BS-468/A/Kit .................................................................. 5

1.3 Starting the installation ................................................................................................... 5

1.4 Installation methods ........................................................................................................ 6

2. DETECTION OF NETWORK’S DEVICES

............................................................................ 7

2.1 WIRELESS KEYPAD DETECTION ........................................................................................ 7

2.2 DETECTION OF WIRELESS DEVICES .................................................................................. 8

3. DEVICE’S INSTALLATION

............................................................................................... 9

3.1 RANGE TESTING USING WIRELESS KEYPAD ..................................................................... 9

3.2 FINAL PLACEMENT OF WIRELESS DEVICES ...................................................................... 9

4. STARTING UP THE INSTALLED SYSTEM ........................................................................ 10

4.1 SYSTEM CONFIGURATION ............................................................................................. 10

4.2 INSTALLATION COMPLETION ......................................................................................... 11

5. DEVICES INSTALLATION .............................................................................................. 11

5.1 Generals ......................................................................................................................... 11

5.2 Device’s control operation

............................................................................................ 12

6. BASIC SYSTEM CONFIGURATION ................................................................................. 12

6.1 Zone settings ................................................................................................................. 12

6.2 Section configuration .................................................................................................... 12

6.3 Entrance, exit, extra time settings ................................................................................. 13

6.4 Zones bypass

–

forced arm ............................................................................................ 13

7. HANDLING THE SYSTEM WITH THE WIRELESS KEYPAD ................................................. 14

7.1 Key Operations and Functions of the Wireless Keyboard ............................................. 14

7.2 Basic Menu .................................................................................................................... 15

7.3 Wireless keypad activation ............................................................................................ 16

7.4 Basic handling and settings ........................................................................................... 16

7.5 Advanced Operations .................................................................................................... 18

7.6 Wireless Zones Events ................................................................................................... 20

Summary of Contents for BS-429/W





























Search results

Summary of Contents for BS-429/W

Reviews:

Related manuals for BS-429/W

Brands by name

Popular brands

olympia electronics BS-429/W, Quick Installation Manual

Search results

Summary of Contents for BS-429/W

Reviews:

Related manuals for BS-429/W

Brands by name

Popular brands