OLT SunShed SSGS1216-FJ-Cedar Assembly Manual Download

Page: 37 / 51

67.

Attach

Bottom Skirting - Bevel

around the base of the

shed. Skirting will hide floor framing. Gaps on outside will be cov-
ered by trim pieces later. Start with front and rear skirting pieces
first and attach with

4 - 1 1/2” finishing nails

per piece.

Parts (Step 67)

Bottom Skirting-Bevel

(1/2” x 4 1/2” x 45 1/4”)

x 14

Hardware (Step 67)

1 1/2” - Finishing Nails

x 56 total

Rear of Shed

Side of Shed

68.

Position

Narrow Door Trim

on left side of door opening and

one

Door Trim

on right side of door. Right side will sit flush with

Door Jamb

. Left side will sit flush on edge of

Narrow Wall

. Do a

dry run with the

Horizontal Gable Trim

from

Step 88

to determine

vertical location of right trim, left trim will sit below

Drip Edge

installed in

Step 25

. Attach with

8 - 1 1/2” Finishing Nails

per

piece.

Parts (Step 68)

Narrow Door Trim

(1/2” x 2 1/2” x 79”)

x 1

Door Trim

(1/2” x 3 1/2” x 85”)

x 1

Hardware (Step 68)

1 1/2” - Finishing Nails

x 16 total

Vertical position determined
by Horizontal Gable trims.

Rear of Shed

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 37

Summary of Contents for SunShed SSGS1216-FJ-Cedar




















































Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands

OLT SunShed SSGS1216-FJ-Cedar, Assembly Manual

Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands