OLT SunShed SSGS1216-FJ-Cedar Assembly Manual Download

Page: 31 / 51

53.

Locate 2nd

Center Roof Panel

and position so plywood is 1/8” from end of Rafters as per

Step

. From side-to-side, make sure Roof Panel is sitting equally on rafters. When positioned correctly,

screw down with

2 - 2 1/2” screws

into outside lower shingles.

54.

Lift up and place remaining

Long Outside Roof Panel

on Rafters. With

Outside Roof Panel

centered on rafter and aligned as per

Steps 50 - 51

, screw panel down with

1 - 2 1/2” screw

Shingles overhanging
outside of roof plywood

55.

Locate

Short Right Roof Panel

. Lift and place panel on polygal

side of roof. Position

Short Right Roof Panel

equally on seam of dou-

bled up Rafter as per

Step 51

. Align Roof Panel at top so even with long

panel at peak. Reach through opening in Rafters to attach. When posi-
tioned correctly, screw down with

1 - 2 1/2” screw

in bottom row of shin-

gles as illustrated above.

Hint:

work from inside of shed to position and

secure Polygal Side Roof Panels.

Parts (Step 55 - 56)

Short L&R Roof Panels

(48” x 37 1/2”)

x 2

Short Center Roof Panels

(45 1/2” x 37 1/2”

)

x 2

Hardware (Step 55 - 56)

- 2 1/2” Screws

x 6

total

Small Gap between roof
panels at peak

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 31

Summary of Contents for SunShed SSGS1216-FJ-Cedar




















































Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands

OLT SunShed SSGS1216-FJ-Cedar, Assembly Manual

Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands