OLT SunShed SSGS1216-FJ-Cedar Assembly Manual Download

Page: 20 / 51

30.

Position and attach

Side Top Plates

Side

Riser Plates

. 65 3/4” side plates are on the outside

with the 45 1/2” plate in the center. Angle of

Side

Plates

should match angle of

F&R Top Wall

Plates

. Attach each piece with

4 - 1 1/4” screws

Complete both sides of shed.

Parts (Steps 30)

Side Top Plates

(3/4” x 2 1/2” x 45 1/2”)

x 2

(3/4” x 2 1/2” x 65 3/4”)

x 4

Hardware (Steps 30)

- 1 1/4” Screws

x 24

total

Top and Side
plates flush

31.

Locate Triangular

Gable Half Walls

for both

sides of shed. Align framing and wall siding lap
together. Screw center wall framing of each piece
together with

4 - 2 1/2” screws

. Note: Prior to

attaching, try each combination of Gables for best
fit.Tip of Gables are separate pieces that need to be
attached on in

Step 32

Parts (Steps 31-32)

Gable Half Walls x 4

Hardware (Steps 31-32)

- 2 1/2” Screws

x 8

total

S3 - 2” Screws

x 8 total

Male / Female Gable
Siding Overlap

Gable End tucked inside
Gable.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 20

Summary of Contents for SunShed SSGS1216-FJ-Cedar




















































Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands

OLT SunShed SSGS1216-FJ-Cedar, Assembly Manual

Search results

Summary of Contents for SunShed SSGS1216-FJ-Cedar

Reviews:

Related manuals for SunShed SSGS1216-FJ-Cedar

Brands by name

Popular brands