manualshive.com logo in svg

OLT SunShed Garden Shed SSGS1212-AK-METAL, Assembly Manual

The OLT SunShed Garden Shed SSGS1212-AK-METAL is a sturdy and practical storage solution for your outdoor space. With its durable metal construction and spacious interior, it's perfect for keeping your gardening tools and supplies organized. Assembly is a breeze with our comprehensive Assembly Manual, which you can download for free from our website manualshive.com.

Share
Download
background image

Note:

 The floor will be flipped over and floor  

runners will sit on your foundation.  It is  
important to note that having a level foundation 
is critical. Choosing a foundation will vary 
between regions.  Typical foundations can be 
concrete pads or patio stones positioned  
underneath the floor runners.

9.

 With Floor Runners attached, carefully flip the floor over and place on your foundation.   

Caution: 

you will need 2 people to assist you. Be careful when laying floor down not to bend or twist 

floor. When in place, level floor completely.

Concrete Slab 
Foundation

Foundations

6.

 Attach 

Floor Runners

 to completed floor 

frame. There are 2 floor runners per 136 1/2” 
side and 5 completed runners in total. Use  

6 - 2 1/2” screws

 per Runner.

7.

 Make sure Runners are flush with outside and 

front and rear floor framing, not overhanging.

8.

 Complete all Floor Runners.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 9

Summary of Contents for SunShed Garden Shed SSGS1212-AK-METAL














































Reviews:

No comments

Related manuals for SunShed Garden Shed SSGS1212-AK-METAL

Palmako EL18-6774 Installation Manual preview
EL18-6774
Brand: Palmako Pages: 44
G21 Boston 523 Manual preview
Boston 523
Brand: G21 Pages: 52
Palmako FR28-4130 Installation Manual preview
FR28-4130
Brand: Palmako Pages: 63
Palmako PAY44-5742 Instruction Manual preview
PAY44-5742
Brand: Palmako Pages: 64
Backyard Products 16835-W Assembly Manual preview
16835-W
Brand: Backyard Products Pages: 84
Karibu AMBERG 3 Manual preview
AMBERG 3
Brand: Karibu Pages: 35
Palmako Klara Installation Manual preview
Klara
Brand: Palmako Pages: 61
OLT GS84-S Assembly Manual preview
GS84-S
Brand: OLT Pages: 36
Palmako 1123113 Installation Manual preview
1123113
Brand: Palmako Pages: 55
Waltons 01PTCOR0707-V1 General Instructions Manual preview
01PTCOR0707-V1
Brand: Waltons Pages: 7
Power Pent Instruction Manual preview
Pent
Brand: Power Pages: 18
Mercia Garden Products 05DTMBPN0503DD-V1 Assembly Instructions Manual preview
05DTMBPN0503DD-V1
Brand: Mercia Garden Products Pages: 8
Mercia Garden Products 04GREEN0806SD-V6 General Instructions Manual preview
04GREEN0806SD-V6
Brand: Mercia Garden Products Pages: 12
Mercia Garden Products 03WES1208-V2 General Instructions Manual preview
03WES1208-V2
Brand: Mercia Garden Products Pages: 9
Mercia Garden Products 03WES1008-V1 General Instructions Manual preview
03WES1008-V1
Brand: Mercia Garden Products Pages: 9
Mercia Garden Products 03WES0808-V1 General Instructions Manual preview
03WES0808-V1
Brand: Mercia Garden Products Pages: 9
Mercia Garden Products 03VER0808-V2 General Instructions Manual preview
03VER0808-V2
Brand: Mercia Garden Products Pages: 8
Mercia Garden Products 03HEL1008DDFW-V2 Instructions Manual preview
03HEL1008DDFW-V2
Brand: Mercia Garden Products Pages: 7

Brands by name

Popular brands

Load more brands