OLT SunShed Garden Shed SSGS1212-AK-METAL Assembly Manual Download Page 37

Page: 37 / 45

Side Bottom Skirting

Bottom Skirting

78.

When correctly aligned, attach with 8 - 1 1/2” finishing nails per piece. Complete remaining

Corner Trim attachments.

Wide T

rim

Narrow T

rim

Front of Shed

76.

Attach

Filler Trim

(4 - 1/2” x 2 1/2” x 75”) to front and rear walls in each corner. Attach with

8 - 1 1/2” finishing nails per piece. Strips are positioned flush with siding and bottom skirting.

77.

Attach

Wide Corner Trim

and

Narrow

Trim

in each corner. Wide Trims are 4 1/2”

wide, Narrow Trims are 2 1/2” wide. Begin with
narrow trim on side of shed, aligning tight
underneath Soffit and even with front of filler
trim. Wide Trim will cap Narrow, as shown in

Step 78. Note that trim may sit slightly
below Bottom skirting when correctly
aligned.

Wide Trim

Narrow Trim

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 37

Summary of Contents for SunShed Garden Shed SSGS1212-AK-METAL














































Search results

Summary of Contents for SunShed Garden Shed SSGS1212-AK-METAL

Reviews:

Related manuals for SunShed Garden Shed SSGS1212-AK-METAL

Brands by name

Popular brands

OLT SunShed Garden Shed SSGS1212-AK-METAL, Assembly Manual

Search results

Summary of Contents for SunShed Garden Shed SSGS1212-AK-METAL

Reviews:

Related manuals for SunShed Garden Shed SSGS1212-AK-METAL

Brands by name

Popular brands