manualshive.com logo in svg

OLT SunShed Garden Shed SSGS1212-AK-METAL, Assembly Manual

The OLT SunShed Garden Shed SSGS1212-AK-METAL is a sturdy and practical storage solution for your outdoor space. With its durable metal construction and spacious interior, it's perfect for keeping your gardening tools and supplies organized. Assembly is a breeze with our comprehensive Assembly Manual, which you can download for free from our website manualshive.com.

Share
Download
background image

83. 

Attach 

Facia Cleat (3/4” x 1 1/2” x 36 1/2”)

 centered on underside of battens on the polygal 

roof side of the shed, flush to edge. Attach  

Facia Cleats (3/4” x 1 1/2” x 40”)

 to the underside of 

Battens

, flush to edge, opposite the polygal roof side of the shed. Repeat this step on the rear side of 

shed. Fasten with 3 - 1 1/4” screws per piece.

 

81. 

Position and attach Mid Ridge Caps evenly spaced 

on mid rafters. Align top to bottom as per

 Step 80

82. 

Align and attach remaining Ridge Caps (3 1/2” wide) over Double Rafters as per 

Step 81

  

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 39

Summary of Contents for SunShed Garden Shed SSGS1212-AK-METAL














































Reviews:

No comments

Related manuals for SunShed Garden Shed SSGS1212-AK-METAL

Rowlinson Gainsborough Gazebo Assembly Instructions preview
Gainsborough Gazebo
Brand: Rowlinson Pages: 5
Palmako Rasmus 1 Installation Manual preview
Rasmus 1
Brand: Palmako Pages: 56
Palmako EL18-4633 Installation Manual preview
EL18-4633
Brand: Palmako Pages: 31
Solid S8949 Manual preview
S8949
Brand: Solid Pages: 32
Keter 17204172 User Manual preview
17204172
Brand: Keter Pages: 33
Palmako ELU18-4555-1 Instruction Manual preview
ELU18-4555-1
Brand: Palmako Pages: 27
Palmako ELT18-3422-1 Installation Manual preview
ELT18-3422-1
Brand: Palmako Pages: 30
Palmako F44-3838 Installation Manual preview
F44-3838
Brand: Palmako Pages: 44
Palmako B28-3226 Installation Manual preview
B28-3226
Brand: Palmako Pages: 43
Palmako FR34-3553-3 Installation Manual preview
FR34-3553-3
Brand: Palmako Pages: 103
OLT 12x12 SpaceMaker Garden Shed Assembly Manual preview
12x12 SpaceMaker Garden Shed
Brand: OLT Pages: 46
Palmako Harry Installation Manual preview
Harry
Brand: Palmako Pages: 43
Palmako ELB16-2217 Installation Manual preview
ELB16-2217
Brand: Palmako Pages: 25
Palmako Zerna Installation Manual preview
Zerna
Brand: Palmako Pages: 54
Palmako PA28-4530 Installation Instructions Manual preview
PA28-4530
Brand: Palmako Pages: 72
Palmako FRO44-3857 Installation Manual preview
FRO44-3857
Brand: Palmako Pages: 56
Palmako FRF28-2929-1 Installation Manual preview
FRF28-2929-1
Brand: Palmako Pages: 52
Palmako FR34-5345 Installation Manual preview
FR34-5345
Brand: Palmako Pages: 59

Brands by name

Popular brands

Load more brands