OLT GS124-SLIDER-CEDAR-FJ Assembly Manual Download Page 3 | Manualshive

Page: 3 / 42

background image

Foundation Types for 12x4 Garden Shed

Concrete Slab Foundation:

- Slab must be at least the same size as assembled floor frame (45 1/2” x 141 1/2”) or larger.
- 6” Deep foundation.
- 0.9 Cubic Yards of concrete required.
- A concrete slab will have the longest durability out of your foundation options.

Once level, a concrete slab is the easiest surface to build on.

Gravel with 4x4 Pressure Treated Stringers:

- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 1.2 Cubic Yards of gravel required, approximatley 11 wheelbarrows.
- 3 - 4x4 Pressure Treated Stringers 12’ long required.
- Evenly spaced, with one at each end of floor frame.

Saves money on materials, easy to level and work with.

Gravel with Patio Paver Stones:

- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 1.2 Cubic Yards of gravel required, approximatley 11 wheelbarrows.
- 21 patio pavers (8” x 8” or larger).
- Center patio paver stones underneath floor runners and underneath seams in floor joists.

Patio paver stones are widely available from most landscape stores

.

141 1/2”

45 1/2”

45 1/2”

141 1/2”

153 1/2”

57 1/2”

3 - 4”x4”x144”

21 Patio Stones

Floor Frame

Concrete Foundation

Completed Foundation

17 1/2”

Gravel Foundation

Gravel Foundation with treated stringers

Completed Foundation

Completed Foundation

153 1/2”

57 1/2”

Gravel Foundation

Gravel Foundation with Patio Pavers

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 3

«
1
2
3
4
5
...
»

Summary of Contents for GS124-SLIDER-CEDAR-FJ











































Reviews:

No comments

Related manuals for GS124-SLIDER-CEDAR-FJ

Brand: Campania International Pages: 3

Brand: Vaxcel Pages: 10

Brand: VARSITY Scoreboards Pages: 10

Brand: Oasis Pages: 2

Brand: Data General Pages: 58

Brand: Woody Valley Pages: 50

Soft Sides ECDFPW314C

Brand: Elkay Pages: 4

Brand: Halsey Taylor Pages: 12

FT-118 Moderne Fountain

Brand: Campania International Pages: 4

Classic Aqua Jump 25

Brand: Rave Sports Pages: 24

System Storage EXN2000

Brand: IBM Pages: 14

Brand: V-TAC Pages: 3

Cayman PIT1014A

Brand: Safavieh Furniture Pages: 3

Brand: Salewa Pages: 19

Fairmont Garden Shed

Brand: YardCraft Pages: 29

Joan Gaspar Vetra S

Brand: marset Pages: 4

Brand: Gyrocopters Pages: 5

Recessed Mounted Pan Door Medicine Cabinets 935/936

Brand: NuTone Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands