OLT 12x8 Studio Garden Assembly Manual Download Page 36

Page: 36 / 43

Small gap
between trims.

Filler Trims will get
covered in

Steps

81-84

with proper

corner trim.

Top Front Wide

(22° scarf bottom /11°cut top)

Bottom Front Wide

(22° scarf top)

Bottom Front (narrow)

(22° scarf top)

Top Front (narrow)

(22° scarf bottom)

Rear Side Wide

(11°cut top)

Rear Corner
(narrow)

Front (narrow)

caps side (wide

)

Scarf joint cuts
on bottoms.

Front

11°cut top.

Outside
Soffit Cap.

1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 36

80.

Position

4R - Filler Trim

(they serve as nailing

strips) in corner of side wall, aligned flush with top of
bottom skirting. Attach with

4 - 1 1/4” Screws

and

repeat for all 4 corners. Next, attach

4T -

Front/Rear Top Filler Trim

with

2 - 1 1/4” Screws

per piece.

Parts

4R - Filler Trim

(7/8” x 2 1/2” x 72”)

x 4

4S - Front Top Filler Trim

(7/8” x 2 1/2” x 28 1/2”)

x 2

4T - Rear Top Filler Trim

(7/8” x 2 1/2” x 12”)

x 2

Hardware

S2 - 1 1/4” Screws

x 22 total

Parts (Steps 81 - 82)

4U - Top Front Narrow Corner Trim

with 22° scarf cut bottom

(1/2” x 2 1/2” x 46”)

x 2

4V - Top Front Side Wide Corner Trim

with 22° scarf cut bottom / 11° cut top

(1/2” x 5 1/2” x 46 1/2”)

x 2

Hardware (Steps 81 - 82)

(

N1 - 1 1/2” Finishing Nails

) x 56 total

Shipping

package length

restrictions requires

front/side trim to be cut

down in length, scarf joint-

ed and then attached

on assembly.

Reminder:

Orientation of Trim

Pieces is important. Left/Right
pieces are mirror images with
rough side facing outward

81.

There are 2 front corner trim packages (Left/Right) with 4

pieces per package which are needed to complete each corner.
Start with the left side corner trim package by placing

4U - Top Front Narrow Corner Trim

tight underneath soffit cap

and

4V - Top Front Side Wide Corner Trim

tight underneath

rafter facia so it is capped by the narrow trim. When correctly
aligned, attach each trim with

6 - 1 1/2” Finishing Nails

. Have

helper assist by holding trim.

Summary of Contents for 12x8 Studio Garden












































Search results

Summary of Contents for 12x8 Studio Garden

Reviews:

Brands by name

Popular brands

OLT 12x8 Studio Garden, Assembly Manual

Search results

Summary of Contents for 12x8 Studio Garden

Reviews:

Brands by name

Popular brands