OLT 12x8 Studio Garden Assembly Manual Download Page 3

Page: 3 / 43

4. Trim Section Cont.

Soffits Rear

4E:

2 - 3/4” x 3 1/2” x 6 1/2” (Outside L/R Cap)

4F:

2 - 3/4” x 3 1/2” x 67” (Tongue & Groove)

4G:

2 - 3/4” x 2 3/4” x 67” (Tongue cut off - positioned against shed)

4H:

1 - 1/2” x 3 1/2” x 4 1/2” (Center Cap)

Top Horizontal Wall Trim

4I:

1 - 3/4” x 1” x 39” - Front

4J:

2 - 3/4” x 1” x 48 3/4” - Front

4K:

3 - 3/4” x 1” x 45 1/2” - Rear

Facia Trim

4L:

4 - 3/4” x 5 1/2” x 72 3/4” - Front/Rear

4M:

4 - 3/4” x 5 1/2” x 60” - Side (11° cut ends- mirror Image)

4N:

4 - 1/2” x 7 1/2” w x 5 1/2” - Facia Detail Plates

Bottom Skirting Trim

Side and Rear

4O:

7 - 3/4” x 1/2” x 45 1/2” - Bottom Skirting

Front

4P:

1 - 3/4” x 4 1/2” x 39” - Center Bottom Skirting

4Q:

2 - 3/4” x 4 1/2” x 48 3/4” - Outside Bottom Skirting

Corner & Wall Trim

Filler

4R:

4 - 7/8” x 2 1/2” x 72” - Filler Trims (all corners)

4S:

2 - 7/8” x 2 1/2” x 28 1/2” - Filler Trims (Front top)

4T:

2 - 7/8” x 2 1/2” x 12” - Filler Trims (Rear top)

Corner

4U:

2 - 1/2” x 2 1/2” x 46” - Top Front Narrow Corner (22° scarf cut)

4V:

2 -1/2” x 5 1/2” x 46 1/2 -Top Front Side Wide Corner(22° scarf /11°cut top)

4W:

2 - 1/2” x 2 1/2” x 62” - Bottom Front Narrow Corner (22° scarf cut)

4X:

2 - 1/2” x 5 1/2” x 62” - Bottom Front Side Wide Corner (22° scarf cut)

4Y:

2 - 1/2” x 5 1/2” x 91” - Rear Side Wide Corner (11° cut top - mirror)

4Z:

2 - 1/2” x 2 1/2” x 89” - Rear Corner

Side

4AB:

2 - 1/2” x 2 1/2” x 37 3/4” - Top Side (22° scarf /11° cut top - mirror image)

4AC:

2 - 1/2” x 2 1/2” x 62” - Bottom Side (22° scarf cut)

Rear

4AD:

2 - 1/2” x 2 1/2” x 89” - Rear Walls

Pre-Hung Door

(Fiberglass - primed white)

4AE:

1 - 37 1/2” x 80”

Door Trim

4AF:

1 - 3/4” x 2 1/2” x 40” - Above Door Filler Trim (Bevel-install thick end up)

4AG:

2 - 1/2” x 2 1/2” x 84” - Vertical Door Trim

4AH:

1 - 1/2” x 3” x 44 1/2” - Horizontal Door Trim (angle cut - bottom corners)

Windows

4AI:

2 - Large Window Inserts - 30 1/4”w x 35” h

4AJ:

3 - Transom Window Inserts - 35”w x 10 1/8” h

Window Trim Pkgs.

4AK:

Large Windows (2 Pkgs)

Top-1 -36 1/4” 11° cut / Sides - 2 -36 1/8” sq.cut / Bottom- 1 -35 1/4” sq.cut

4AL:

Transom Windows (Left/Right) 2 Pkgs

Top-1 - 41” 11° cut / Sides- 2 -10 5/8” sq.cut / Bottom-1 -40” sq.cut

4AM:

Transom Window (Center) 1 Pkg

2 Horizontal - 35 3/4” - sq.cut / 2 Vertical - 20 1/2” - sq.cut

Miscellaneous Pieces

4AN:

2 pc - Spare Wall Siding (48 1/2” long)

4AO:

8 pcs - Shim Shingles- use to shim door, etc.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 3

Steps

68-69

71-76

77-79

81-83

86-87

88-89

90-93

If you plan on painting your door, we
suggest doing it prior to construction

Summary of Contents for 12x8 Studio Garden












































Search results

Summary of Contents for 12x8 Studio Garden

Reviews:

Brands by name

Popular brands

OLT 12x8 Studio Garden, Assembly Manual

Search results

Summary of Contents for 12x8 Studio Garden

Reviews:

Brands by name

Popular brands