OLT 12x12 SpaceMaker Garden Shed Assembly Manual Download Page 31

Page: 31 / 46

49.

Locate all

Metal Roof Panels

and

Metal Roof Hangers

. To

temporarily help hold the

Metal Roof Panel Long

in place, hook a

Metal Roof Hanger

onto the lower

Batten

approximately where the

center of the first panel will be. Place the first

Metal Roof Panel Long

Battens

. Do not fasten Panels down until

Step 54

. place remaining

Metal Roof Panels

on Hangers the same way.

Parts (Steps 49 - 54)

Metal Roof Panels Long

(86” long)

x 8

Hardware (Steps 49 - 54)

2” - Metal Roof Screws

x 60 total

Hardware (Steps 49 - 54)

Metal Roof Hangers

x 4

total

Metal Roof Panels overlap each other

50.

Metal Roof Panels

overhang on the side of shed should be approximately 4” and is set by

Metal

Roof Hangars

. Overall width past the end of

Battens

on front and rear can vary from

1” - 3” depending on your personal preferences The

Metal Roof Panels

have room to space out to

achieve desired overhang.

4”

1” - 3” of overhang past
the battens.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 31

Summary of Contents for 12x12 SpaceMaker Garden Shed















































Search results

Summary of Contents for 12x12 SpaceMaker Garden Shed

Reviews:

Related manuals for 12x12 SpaceMaker Garden Shed

Brands by name

Popular brands

OLT 12x12 SpaceMaker Garden Shed, Assembly Manual

Search results

Summary of Contents for 12x12 SpaceMaker Garden Shed

Reviews:

Related manuals for 12x12 SpaceMaker Garden Shed

Brands by name

Popular brands