background image

Read the following " PRECAUTIONS" carefully before installation.
The caution items stated here must be followed because these important contents are related 
to safety. The meaning of each indication used is as below.
Incorrect installation due to ignoring of the instruction will cause harm or damage, and the
seriousness is classified by the following indications. 

!

 This indication shows the possibility of causing death or serious injury.

This indication shows the possibility of causing injury or damage to 
properties only.

WARNING

!

  CAUTION

1. Injury means causing harmed, burned, electrical shocked, but not serious for hospitalization.
2. Damage of property means disrepair of property, material.

Carry out test running to confirm that no abnormality occurs after the installation. Then, expl-
ain to user the operation, care and maintenance as stated in instructions. Please remind the
customer to keep the operating instructions for future reference.

Engage dealer or specialist for installation. If installation done by  user is defective, it 
will cause water leakage, electrical shock or fire.

Install according to this installation instructions strictly. If installation is defective, it will 
cause water leakage, electrical shock or fire.

Use the attached accessories parts and specified parts for installation. Otherwise, it will 
cause the set to fall, water leakage, fire or electrical shock.

Install at a strong and firm location which is able to withstand the set's weight. If the stren-
gth is not enough or installation is not properly done, the set will drop and cause injury.

For electrical work, follow the local national wiring standard, regulation and this installa-
tion instructions. An independent circuit and single outlet must be used. If electrical circuit 
capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.

When carrying out piping connection, take care not to let air or other substances other 
than the specified refrigerant go into refrigeration cycle. Otherwise, it will cause lower 
capacity, abnormal high pressure in the refrigeration cycle, explosion and injury.

Grounding is necessary. It may cause electrical shock if grounding is not perfect.

Do not install the unit at place where leakage of flammable gas may occur. In case gas
leaks and accumulates at surrounding of the unit, it may cause fire.

!

WARNING

NOTE :

 PRECAUTIONS

It suits for 36000

48000Btu/h  cooling  and heating capacity  type.When the outdoor

temperature is lower than 6 c,the system should be electrified over 12 hours.

1

Summary of Contents for OSH-T24HRK3






































Reviews: