oldfields Treco A107S, Manual

Page: 4 / 36

A x B C D x E X x Y
• 4 •
INSTALLATION ADVICE
ENGLISH
• Check the label on the pack to ensure you have the model shed you ordered.
Please retain info on model No. at the end of the carton.
THIS MANUAL WILL BE USED FOR THE FOLLOWING GARDEN SHED MODEL NUMBERS.
MODEL No. APPROX. ROOF OVERALL APPROX. BASE APPROX. FOUNDATION DYNABOLT
DIMENSIONS HEIGHT DIMENSIONS DIMENSIONS 6mm x 40mm
ZINCALUME COLOURBOND feet mm feet mm feet mm feet mm Qty.
BEFORE YOU START, IT IS IMPORTANT THAT YOU READ THE FOLLOWING INSTRUCTIONS.
• When selecting a site, choose an area that is firm and level yet allows drainage away from the site.
• Although this shed when installed according to instructions, is designed to withstand greater wind loads than other
conventional sheds, do not assemble it in areas subject to high winds or erect on a windy day. Any building left
partially constructed may be seriously damaged if left in this state. It is your responsibility to safely and securely anchor the
shed, having regard to the windiest conditions in the area. The shed could possibly blow away causing damage and
possible injury if not properly attached to the ground foundation.
• Do not backfill against the walls or base of the shed as this will cause corrosion and void the warranty.
• The prevention of condensation inside the shed will assist in keeping the contents dry as well as minimising any possible
corrosion of the shed itself, the following hints may prove useful.
There is always dampness in soil, and this may rise into the shed if there is no barrier. A heavy duty polythene sheet may
be placed under the concrete slab to prevent evaporation into the shed.
Seal the space between the bottom frame and the concrete slab with a mastic (except at the front corners). The front
corners are not sealed to enable drainage out of the ends of the front base rail.
If condensation still presents a problem, panels of polystyrene (5cm thick) may be glued to the interior of the roof between
the supports. Use a glue that is resistant to moisture and temperature.
• You will need a few tools, as indicated in the section HOW TO READ THIS MANUAL. All holes for screws are
predrilled. A power screw driver or cordless drill equipped with a magnetic Philips tip will hasten assembly. Take care not
to over-tighten self-tapping screws.
• Sort, separate and identify all parts and hardware before construction. Check against the illustrations shown. Framing
components are labelled except for panels.
• Since this manual is used to instruct assembly of varying sizes of shed, Labelling of Parts in the diagrams has been
simplified as follows:
All the frame work components have the same system of part numbers but indicate different lengths, these part numbers
are stamped into the component.
e.g. Roof Beams 9 foot length = P9
7 foot length = P7
5 foot length = P5
Therefore, in the diagrams the Roof Beam is labelled P.
IMPORTANT SAFETY FEATURES
• Observe all special notes which indicate differences between various types of sheds.
• You should not try to assemble the shed on your own. Get a second person to help you.
• The statutory requirements of the local building authorities must be observed.
• Safety gloves should be worn during assembly.
• Safety glasses should be worn during assembly.
• Preferably in a long sleeve shirt.
• Beware of sharp edges.
• WINTER SERVICE: The roof is designed for a snow load of 75 kg/m2. In order to avoid overload of the roof, timely
removal of snow from the roof area is recommended.
If the garden shed is unattended for lengthy periods during the winter months, the roofs should be propped up as a safety
precaution.
THE MANUFACTURERS CANNOT BE HELD RESPONSIBLE FOR ANY CONSEQUENCES DUE TO SHEDS THAT ARE
NOT ERECTED PER INSTRUCTIONS OR FOR DAMAGE DUE TO WEATHER CONDITIONS OR ACTS OF GOD. PARTS
MAY CONTAIN SHARP EDGES & CORNERS. CARE MUST BE TAKEN WHEN HANDLING VARIOUS PIECES TO AVOID A
MISHAP, FOR SAFETY SAKE, PLEASE USE A PAIR OF WORK GLOVES & EYE PROTECTION WHEN ASSEMBLING OR
PERFORMING ANY MAINTENANCE ON THE BUILDING.
Z107S
Z109S
A107S
W107S
FG107S
IH107S
A109S
W109S
FG109S
IH109S
6´8´´
6´8´´
19
21
2030
2030
10´ x 7´
10´ x 9´
3070 x 2160
3070 x 2780
9´8´ x 6´8´´
9´8´ x 8´8´´
10´ x 7’
10´ x 9’
2960 x 2080
2960 x 2680
3070 x 2160
3070 x 2780
Note: All dimensions are approximate. All dimensions in mm. 1 Foot = 30.48cm. Dynabolts are NOT supplied.
FG = Federation Green, IH = White and W = Wheat assembly is the same as Zincalume.
PLEASE REFER TO SEPERATE PARTS LIST FOR FG, W AND IH.