background image

Any information contained in these operating instructions may be changed without prior notice.

OKM does not make any warranty for this document. This also applies without limitation to implied assurances of 

merchantability and fitness for a specific purpose. OKM does not assume any responsibility for errors in this manual 

or for any incidental or consequential damage or loss associated with the delivery, exploitation or usage of this 

material.

This documentation is available "as presented" and without any kind of warranty. In no circumstances OKM takes 

responsibility for lost profits, usage or data loss, interruption of business activities or all kind of other indirectly 

damages, which developed because of errors in this documentation. This instruction manual and all other stored 

media, which are delivered with this package should only be used for this product. Program copies are allowed only 

for security- and safety purposes. The resale of these programs, in original or changed form, is absolutely forbidden.

This manual may not be copied, duplicated or translated into another language, neither in part nor completely, over 

the copyright matters without the prior written consent of OKM.

Copyright ©2002 – 2011 OKM GmbH. All rights reserved.

Summary of Contents for Bionic X4































Reviews: