English
3
Federal Communications Commission
(FCC)
FCC Declaration of Conformity for 120-Volt
Models
1. Product Identification
Product Name: Executive Series 1220n
Model No.: N31130A
2. Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
3. Responsible Party
Oki Data Americas, Inc.
2000 Bishops Gate Boulevard
Mt. Laurel, NJ 08054-4620
1-800-654-3282 (1-800-OKI-DATA)
FCC Radio Frequency Interference Statements
120-Volt Models
WARNING: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Plug the unit into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Note:
It is the responsibility of the user to obtain the
required shielded cable in order to ensure
compliance of this equipment with FCC regulations.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.
Industry Canada (IC)
IC Radio Interference Statements
120-Volt Models
This Oki Data apparatus complies with the Class B limits
for radio interference as specified in the IC Radio
Interference Regulations.
European Union Council of the
European Communities (EUCEC)
EUCEC Statements of Conformance
Electromagnetic Conformance
This product complies with the requirements of the
Council Directive 89/336/EEC on the approximation of
the laws of the member states relating to electromagnetic
compatibility.
Safety Conformance
This product is in conformity with Directive 73/23/EEC
on the harmonization of the laws of Member States
relating to electrical equipment designed for use within
certain voltage limits.
Safety Information
Your OKI printer has been carefully designed to give you
years of safe, reliable performance. As with all electrical
equipment, there are a few basic precautions you should
take to avoid hurting yourself or damaging the printer.
• Carefully read the provided setup and operating
instructions.
• Save all provided documentation for future reference.
• Read and follow all warning and instruction labels on the
printer itself.
• Unplug the printer before you clean it. Use only a damp
cloth. Do not use liquid or aerosol cleaners.
• Place your printer on a firm, solid surface. If you put it on
something unsteady, it may fall and be damaged. If you
place it on a soft surface, such as a rug, sofa, or cushion,
the vents may be blocked, causing the printer to overheat.
• Protect your printer from overheating. Make sure no
obstructions block the openings of the printer. Do not put
the printer on or near a heat source (such as a radiator or
heat register). Keep the printer out of direct sunlight.
Allow enough room around the printer for adequate
ventilation and easy access to the paper trays. If you put
the printer in any kind of enclosure, make sure the
enclosure is properly ventilated.
• Do not use your printer near water. Do not spill liquid of
any kind into it.
• Be certain that your power source matches the rating listed
on the back of the printer. If you are not sure, check with
your dealer or with your local power company.
• Your printer has a grounded, three-prong plug as a safety
feature. This plug only fits into a grounded outlet. If the
plug does not fit, the outlet may be an older, non-grounded
