Oki B431L6 Maintenance Manual Download Page 121

Page: 121 / 184

6. Procedures for Repairing

Oki Data CONFIDENTIAL

44983601TH Rev.1

6-12 /

[Jam Error]

-1 Paper feed jam

• Does a jam error occur when turning on the power?

• Yes

Is there any paper in the entrance sensor?

• Yes

Remove the paper

• No

Does the entrance sensor lever work normally? (It moves freely by touching.)

• No

Replace the entrance sensor lever.

• Yes

Clean the entrance sensor, or replace the main board.

• No

A jam error occurs after feeding paper.

• Yes

Is the paper sent to the entrance sensor lever?

• Yes

Does the entrance sensor lever work normally? (It moves freely by touching.)

• No

Replace the entrance sensor lever.

• Yes

Is the IN_WR connector of the main board connected properly?

• No

Connect the IN_WR connector properly.

• Yes

Clean the entrance sensor, or replace the main board.

• No

Replace the paper feed roller, pick-up roller or paper cassette.

• No

Does the paper feed roller rotate?

• Yes

Set the paper cassette appropriately.

• No

Does the paper feed clutch work normally?

• Yes

Replace the paper feed roller and shaft.

• No

Is HCLT connector of the main board appropriately connected?

• No

Connect HCLT connector appropriately.

• Yes

Is the coil resistance of the paper feed clutch (Normal resistance: Pin1, Pin2, and approx.

192

) normally?

• No

Replace the paper feed clutch.

• Yes

Replace the main board.

Ejection sensor

Paper ejection roller

Heat roller

Transfer roller

Write sensor

Regist roller

Entrance sensor

Paper-end sensor

Pick-up roller

Feed roller

per f

eed or

ientation

Summary of Contents for B431L6

























































































































































































Search results

Summary of Contents for B431L6

Reviews:

Oki B431L6, Maintenance Manual, Page: 121 / 184

Search results

Summary of Contents for B431L6

Reviews: