Oilon RP-130 H Operation And Maintenance Manual Download | Manualshive

Page: 5 / 58

background image

1.

1.

General

General

1.1.

1.1.

Forewords

Forewords

Thank you for using Oilon-products. We hope you are content with the product and our
service. This manual is intented to guide operation and maintenace of the product. We
pursue to improve our products and services. Therefore we readily accept feedback
about on our operation and maintenance manuals. Feedback may be sent to info@oilon.
com

Installation and maintenance of the device must be performed by a certified personnel. If
you need help with maintenance issues, please contact your nearest representative or
Oilon Oy technical support. Contact information can be found on our website at www.
oilon.com

1.2.

1.2.

Conventions in this Manual

Conventions in this Manual

1.2.1

1.2.1

Warning symbols in this manual

Warning symbols in this manual

Read these instructions carefully before installation, commissioning or maintenance of
the burner. The given instructions must be followed.

Symbols used are :

Be careful. The DANGER symbol indicates a possible danger of bodily
harm or lethal injury.

Pay attention. The CAUTION sign indicates a possible danger of
damage to the device, components or surroundings.

Notes indicate tips, hints and other essential information.

KEEP THIS MANUAL ALONG WITH THE INSTALLATION RECORD AND THE
ELECTRICAL SCHEMES AVAILABLE NEAR THE BURNER!

RPMARINES 30870641GB

5 (58)

1. General

«
...
3
4
5
6
7
...
»

Summary of Contents for RP-130 H



























































Reviews:

No comments

Related manuals for RP-130 H

Brand: Uberhaus Pages: 16

Brand: DCS Pages: 22

Brand: LOCO COOKERS Pages: 48

Slimline SB1100C

Brand: ICON FIRES Pages: 13

Brand: Wood Stone Pages: 43

Brand: GRAND EFFECTS Pages: 24

Brand: Oilon Pages: 134

Brand: Gasmate Pages: 20

Brand: Nu-Way Pages: 55

Brand: Unigas Pages: 131

Brand: Unigas Pages: 149

Brand: Uberhaus Pages: 16

Brand: Riello Pages: 44

Brand: Unigas Pages: 120

Brand: Unigas Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands